Write a program to find the average of 32 bytes started at memory location [Mem 1]. If the average is greater than 42H then store the average at memory location [Mem 2] otherwise, store it at memory location [Mem 3].(microprocessor)
Q: Write an assembly language program for the 8085 Microprocessor to find the smallest of the given…
A: Assembly language program to compare and find smallest among it.
Q: Assume that an integer greater than 2 and less than 32,768 is deposited in memory location A by…
A: Solution :: ORIG x3000 AND R4, R4, #0 LD R0, A NOT R5, R0 ADD…
Q: Suppose you have 200B memory space where data is stored and you wish to search a data value of 1AH…
A: GIVEN THAT, The assembly code is 1AH.
Q: In a microcomputer, the addresses of memory locations are binary numbers that identify each memory…
A: Micro computer which refers to the very small computer that relatively uses an inexpensive computer…
Q: For this assignment, you are to write a MIPS assembly language program using the MARS IDE and assume…
A: Answer :
Q: A- write a program to count number of one's & zero's in a number stored at 0200:0010, use rotate…
A: Near call: A call to a procedure within the current code segment (the segment currently pointed to…
Q: Given the following memory maps, determine the size of available memory space (ie the unused or free…
A: ANSWER:-
Q: 1- Write an assembly language program to search for data 44 In 9 memory locatlons start at (8000) If…
A: 1. .code main: MOV SI,8000H ; si points to memory 8000H MOV CX,9 ; set…
Q: Given the following memory values and a one-address machine with an accumulator, what values do the…
A: Actually, the operand which is stored n particular memory location is called as addressing mode.
Q: Write a program in assembly language to put the value 80H into 30 RAM locations starting at RAM…
A: We have to write program in assembly language to put the value 80H into 30 RAM locations starting at…
Q: Write x86 assembly program to convert n kilobytes to the equivalent gigabyte, megabyte and kilobyte…
A: Program to convert n kilobyes to the equivalent giabtye,megabyte and bytes.
Q: Addressing Memory Suppose that there are 226 bytes in memory. In binary the lowest address is…
A: Note: Answering the first three subparts as per the guidelines. Given Data : 226 bytes in memory…
Q: 1. Suppose a program has 15 logical instructions (from 0). It has been loaded into the RAM at memory…
A: given data, memory address (1234ABCD)16 Number of instructions = 5
Q: For this assignment, you are to write a MIPS assembly language program using the MARS IDE and assume…
A: datavAddr: .asciiz "The address "vPage: .asciiz " is in: Page number = "vOff: .asciiz " Offset = "…
Q: 2-Write the program to compute (W) from the following equation X x Y W = Microprocessor %3D Z
A: you have not mentioned programming language I am going to solve this question using the C language…
Q: Write a Java program that prompts the user for the page size used in a virtual memory system; this…
A: A Java program that accepts a valid system page size and virtual address and calculates the page…
Q: 6. Suppose the RAM for a certain computer has 256M words, where each word is 32 bits long. a) What…
A: Step 1 The answer is given in the below step;
Q: Consider an assembly language that has a 2-address ISA set. | The instructions that are available in…
A: Given registers R1, R2, R3 and we cant change original values of operands and 4 value is cant take…
Q: Suppose that a program does read operations on the following memory addresses (e.g., with “lb” or…
A: Question Suppose that a program does read operations on the following memory addresses (e.g., with…
Q: the starting address of the RAM is 00000H. RAM1 = 64K , RAM2 = 64K , RAM3 = 32K , RAM4 = 64K ,and…
A: The starting addresses of all memory chips are integer multiple of the sizes of the corresponding…
Q: The following is a code segment with a routine named MAIN which calls a subroutine named SUB. X, Y,…
A: At point C d0, d1, a0 d0, d1, a0 d0, d1, a0 d0, d1, a0 d0, d1, a0 d0, d1, a0 local vars local…
Q: 1. Consider memory storage of a 32-bit word stored at memory word 34 in a byte- addressable memory.…
A: Note - answer only one question at time of you want answer of another question post it separately…
Q: Suppose you have a RISC machine with a 2 GHz clock (ie, the clock ticks 2 billion times per second).…
A:
Q: If the code is compiled on a 32-bit machine. The next code will print? short s; printf("Size of…
A: For shorter range datatypes, the size remains same for both 32 and 64 bit machines
Q: 1- Write an assembly language program to search for data 44 in 9 memory locations start at (8000) if…
A: 1. .code main: MOV SI,8000H ; si points to memory 8000H MOV CX,9 ; set CX=9…
Q: Write a program for 8085 microprocessor to swap nibbles (upper four bits and lower four bits) of ten…
A: 8085 is an 8-bit microprocessor as it operates on 8 bits at a time and is created with N-MOS…
Q: 1. Consider memory storage of a 32-bit word stored at memory word 34 in a byte- addressable memory.…
A: Given word= 34 of 32 bit find:- (a) What is the byte address of memory word 34? (b) What are the…
Q: 1. Consider memory storage of a 32-bit word stored at memory word 42 in a byte- addressable memory.…
A: NOTE: ACCOEDING TO COMPANY POLICY WE CANNOT SOLVE MORE THAN THIS. YOU CAN RESUBMIT THE QUESTION…
Q: int i = 5; is a statement in a C program. A. during execution, value of i may change but not its…
A: Option C :- repeated execution may result in different addresses for i .
Q: Assume a CPU with a fixed 32-bit instruction length has the following instruction forma
A: a. Op code + mode = 7 + 5 = 12 bits, leaving 22 bits for the operands. With 3 registers,each uses 9…
Q: 4. The Single Instruction Computer (SIC) has only one instruction that can do all operations our…
A: Given:
Q: 2- Write an assembly program to implement the following equation : Y 20 4 +3-2
A: 2- Write an assembly program to implement the following equation : Y= 20 / 4 +3-2
Q: Write a program to multiply the contents of the PINB by the contents of the RAM location 0x600 and…
A: The complete program is given below fill the blanks in accordance with it. IN is used to take input…
Q: 1- Write an assembly language program to search for data 44 in 9 memory locations start at (8000) if…
A: First Step: An assembly language program to search for data 44 in 9 memory locations start at…
Q: write a program to move the data from external memory location 25h to P1 and then from P1 to R5
A: 1. load r2 to data 25h2. load 9000h into dptr3. then load data 0a0h4. move p1 to data 00h5. now…
Q: Consider memory storage of a 64-bit word stored at memory word 32 in a byte-addressable memory
A: ANSWER : a) Each data byte has a unique address. A 32-bit word consists of four 8-bit bytes. So…
Q: Write a program to add the following data and store the result in RAM location 40H. ORG 300H…
A: Given: We have to write an assembly program add the following data and store the result in RAM…
Q: Q4/ A- write a program to count number of one's & zero's in a number stored at 0200:0010, use rotate…
A: program to count number of ones and zeros are given below
Q: Suppose a program’s 15-th logical instruction (counting starts from zeroth) is at physical address…
A: Dear Student, Assuming the Addresses are byte addressable thus 14 th byte address will be at…
Q: Q1\ Suppose 8086 microprocessor perform the following task: ADD AX, 3FF2H Where the value of AX is…
A: The flag register has following: Status Flag Sign (S) Parity (P) Zero (Z) Overflow (O) Auxiliary…
Q: Write a program in assembly language to put the value 55H into 10 RAM locations starting at RAM…
A: The RAM given location is 140H The value to be copied in Location 140H to 149H is 55H
Q: (a) What is the byte address of memory word 32? (b) What are the byte addresses that memory word 32…
A: Each data byte has a unique address. A 32-bit word consists of four 8-bit bytes.
Q: write a program in ( assembly language (8086) )that compare two blocks of 64 consecutive bytes, the…
A: The assembly level programming 8086 is based on the memory registers. A Register is the main part of…
Q: write a program that does the following: AL=9 AL++ X=AL Using 8086emu program check the status of…
A: Question :-
Q: Required reference strings needed for the Execution is given below 1000 AA 1002 AC 1004 DA 1006 CC…
A: Here we explain : ============================================================================ The…
Q: For a microprocessor, if the total time of all positive cycles in 5 seconds is 2 seconds, and the…
A: Off time for every cycle = Toff = 0.335 microsecond Total time of all positive cycles = Ton = 2…
Q: Write a C program that emulates the logic of the memory management unit (MMU). The following are the…
A: The C program is given in the below steps.
Q: a) Main memory is byte addressable? b) Main memory is word addressable?
A: Given main memory : 1 M x 8 From given memory, total locations are 1M each location size = 8 bits
Step by step
Solved in 3 steps
- In the ________, memory addresses consist of a single integer.Most Intel CPUs use the __________, in which each memory address is represented by two integers.Q1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000H to 3009H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending each of the required bytes, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes. The solution must be integrated and include the calculation of the baudrate delay time Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)
- 8086Microprocessor 2. you have data of size 1010 byte stored in an array starting at 84000H, write a program to rotate each data 3 times to the left and store the result in the same array. (using loop instruction)Write assembly language programs for the 8086 microprocessors to perform multiplication of two matrices Am*n and Bn*p. The value of m = 4, n = 2, and p =3. Assume all the elements in matrices A, B, and answer of the multiplication are 8-bit numbers. Flow chart Pseudocode Assembly Code with brief describe comments (EMU8086 emulator)Q5.Write a multiplication an Intel 8085 assembly program to multiply 2 numbers. The numbers are stored in memory locations 3000H & 3001H. Store the result in memory locations 3002H & 3003H. Show your flow chart and the assembly code. Q6. Answer True or False for the followings: a) Machine code is the assembly code b) Data field is 16 bit while address field is 8 bit c) Trainerkitcanbeused for implementing assembly code d) ADo bus can be used for addressing and datatransfer e) WR and RD pins are on the same pin
- Assume a CPU with a fixed 32-bit instruction length has the following instruction format:opcode mode [operand1] [operand2] [operand3]The mode encodes the number of operands and each operand’s mode. For instance, one mode indicates three registers, another indicates two registers and an immediate datum, another indicates a main memory reference, etc. Assume there are 94 instructions and 22 modes. Answer the following.a. One mode indicates three registers. How many registers can be referenced in this mode?b. One mode indicates two registers and an immediate datum in two’s complement. Assuming there are 32 registers, what is the largest immediate datum that can be referenced?c. One mode has a destination register and a source memory address (an unsignednumber). Assuming 16 registers, what is the largest memory reference available?d. One mode has two memory addresses, both using base displacement. In both, the basesare stored in index registers and the displacements are specified in the…Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending the required byte, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baud rate delay time Transmit Set up Character Bit Counter • Send Start Bit No Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes • Add Parity if Necessary Send Two Stop Bits Return (a)Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
- Use emu8086 –assembler and microprocesser emulator 4.08 language to: Write a program to read a letter in lower case the convert this letter to upper case and print it. (to convert from lower to upper subtract from the value 20h)Q2- The sum of a 100 * 100 matrix (total 10000 number) of floating point numbers is calculated using a parallel program that runs on 10 processors. A single floating point addition of two numbers takes 4 micro seconds. A- Using Amdahl's formula what is the execution time of calculating this sum if each of the 10 processors gets an equal balanced work load. B- Using Amdahl's formula what is the execution time of calculating this sum if one processor gets 2000 numbers of the total work load to sum and the other 9 processors each get an equal load out of the remaining 8000 numbers work load.By assuming that X is the last digit of your student number and 3X is a two digit number, consider memory storage of a 64-bit word stored at memory word 3X in a byte-addressable memory (a) What is the byte address of memory word 3X? (b) What are the byte addresses that memory word 3X spans? (c) Draw the number 0XF1234567890ABCDE stored at word 3X in both big-endian and little-endian machines. Clearly label the byte address corresponding to each data byte value.