working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater. Steam enters t 200°F and expands to 120 lb/in.2, where some of the steam is extracted and diverted to the closed fe eam expands through the second-stage turbine to the condenser pressure of 2 lb/in.² Condensate ex turated liquid at 120 lb/in.² undergoes a throttling process as it passes through a trap into the conden eater at 1400 lb/in.² and a temperature equal to the saturation temperature at 120 lbf/in.2 The net pa MW

working fluid in an ideal regenerative Rankine cycle with one closed feedwater heater. Steam enters t 200°F and expands to 120 lb/in.2, where some of the steam is extracted and diverted to the closed fe eam expands through the second-stage turbine to the condenser pressure of 2 lb/in.² Condensate ex turated liquid at 120 lb/in.² undergoes a throttling process as it passes through a trap into the conden eater at 1400 lb/in.² and a temperature equal to the saturation temperature at 120 lbf/in.2 The net pa MW

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

find the efficiency of the cycle
Compute for the work net and the thermal efficiency of the cycle shown
Fill in the blanks: Determine the efficiency of a constant volume cycle with expansion ratio equal to 7.8. v the "numerical value" No need to
Determine: a)Work of the compressor(kW) b)COP of the cycle
The compression ratio in a gasoline engine is 8. The total cylinder volume of the engine (for the bottom dead point) is 600 ml, and air enters the cylinders at a temperature of 20 ° C and a pressure of 100 kPa andThe maximum temperature of the cycle is known as 1500 ° C. a) Calculate the heat input in the cycle in kJ. b) Calculate the thermal efficiency of the cycle c) Calculate the power generated in the cycle.
Calculate the cycle efficiency
1.4 A diesel engine operating an air standard diesel cycle has 20cm bore and 30cm stroke. the clearance volume is 420cm3. if the fuel is injected at 5% of the stroke, find the air standard efficiency. 1.5 Develop an expression for the thermal efficiency of the air-standard diesel cycle as a function of the compression ratio r. = V1V2 and the expansion ratio r, = V4 / V3. Assume the working fluid is an ideal gas, and the volume effect of moles of gas generated is small relative to the effect of heating from combustion. %3D
1. A Carnot cycle has a maximum temperature of 550 °F and minimum temperature of 100 °F. If the horsepower output of the engine is 44.13, find the heat added for the cycle in BTU/s.
The figure below is the basic plot of pressure vs. volume for the Dual Standard Cycle. Constant pressure heat addition 3 4 PV = constant %3D Heat IN Adiabatic expansion 2 Heat OUT (Constant volume heat rejection) Constant volume heat addition 1 Adiabatic compression Volume (V) Using the Dual Air Standard Cycle and the following data: • Assume constant properties of air. R= 287 J/kgK; Cp = 1005 J/kgK; Cv = 718 J/kgK; y = 1.4 • Cycle compression ratio = 14 (V1/v2) • Air conditions prior to compression: Pressure = 1.3 bar; Temperature = 293K • Heat added at constant volume = 280000 J/kg • Heat added at constant pressure = 662000 J/kg Pressure (P)
Air is used as a working substance in a given internal combustion engine, which is supplied with heat at a constant volume. Based on the data, calculate the The work of the cycle.
Pa Complete the table given below for a closed system undergoing a cycle. Coet Wet Process Wot kJ AUKJ 1-2 21 11 2-3 14 -8 3-4 -5 4-1 4. 6.
A diesel engine in a power plant has an output of 2000 KW at 1000 rpm. It uses fuel oil having a heating value of 42,000 KJ/kg. If the efficiency of the engine is 39.61%. Calculate the sp. gr. of the fuel used and the fuel consumption in barrels per month.