Which part of the D.C motor is used to change the direction of current after a half cycle?a. Carbon brushesO b. Loop or coilO c. Slip ringsO d. Split rings Radio waves are an example ofO a. Transverse waveO b. Longitudinal wavesO c. Sound wavesOd.Mechanical waves

Split ring uses to change the direction of current.

Answered: Which part of the D.C motor is used to…

Science

Physics

Which part of the D.C motor is used to change the direction of current after a half cycle?

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter22: Magnetism

Section: Chapter Questions

Problem 60PE: What are the directions of the currents in the loop and coils shown in Figure 22.61?

See similar textbooks

Similar questions

What is the value of the magnetic flux through the coil in Figure 23.56 (b) due to the wire?
(a) A dc power line for a light-rail system caries 1000 A at an angle of 30.0 to Earth's 5.0105 T field, What is the force on a 100-m section of this line? (b) Discuss practical concerns this presents, if any.
An induction slave heats a pot with a coil carrying an alternating current located beneath the pot (and without a hot surface). Can me stove surface be a conductor? Why won’t a coil carrying a direct current work?
If a current flows in the Satellite Tether shown in Figure 23.12, use Faraday’s law, Lenz'S law, and RHRl to show that there is a magnetic force on the rather in the direction opposite to its velocity.
Suppose you find that the belt drive connecting a powerful motor to an air conditioning unit is broken and the motel is running freely. Should you be worried that the motor is consuming a great deal at energy for no useful purpose? Explain why or why not.
Measurements affect the system being measured, such as the current loop in Figure 22.56. (a) Estimate file field the loop creates by calculating the field at the center of a circular loop 20.0 cm in diameter carrying 5.00 A. (b) What is the smallest field strength this loop can be used to measure, if its field must alter the measured field by less than 0.0100%?
Eddy current are induced currents set up in a piece of metal when it moves through a nonuniform magnetic field. For example, consider the flat metal plate swinging at the end of a bar as a pendulum, as shown in Figure CQ20.9. (a) At position 1, the pendulum is moving from a region where there is no magnetic field into a region where the field B is directed into the paper. Show that at position 1 the direction of the eddy current is counterclockwise. (b) At position 2, the pendulum is moving out of the field into a region of zero field. Show that the direction of the eddy current is clockwise in this case. (c) Use right-hand rule number 2 to show that these eddy currents lead to a magnetic force on the plate directed at shown in the figure. Because the induced eddy current always produces a retarding force when the plate enters or leaves the field, the swinging plate quickly comes to rest. Figure CQ20.9
Integrated Concepts A lightning bolt produces a rapidly varying magnetic field. It the belt strikes the earth vertically and acts like a current in a long straight wire, it will induce a voltage in a loop aligned like that in Figure 23.57 (b). What voltage is induced in a 1.00 m diameter loop 50.0 m from a 2.00106A lightning strike, if the current falls to zero in 25.0s ? (b) Discuss circumstances under which such a voltage would produce noticeable consequences.
What are the directions of the currents in the loop and coils shown in Figure 22.61?
Is the Earth's magnetic field parallel to the ground at all locations? If not, where is it parallel to the surface? Is its strength the same at all locations? If not, where is it greatest?
(a) A car generator turns at 400 rpm when 1he engine is idling. Its 300-turn, 5.00 by 8.00 cm rectangular coil rotates in an adjustable magnetic field 50 that it can produce suf?cient voltage even at low rpms. What is the field strength needed to produce a 24.0 V peak emf? (b) Discuss how this required field strength compares to those available in permanent and electromagnets.
A magnetized sewing needle has a magnetic moment of 9.70 mA m2. At its location, the Earths magnetic field is 55.0 T northward at 48.0 below the horizontal. Identify the orientations of the needle that represent (a) the minimum potential energy and (b) the maximum potential energy of the needlefield system. (c) How much work must be done on the system to move the needle from the minimum to the maximum potential energy orientation?