Which of the following statement(s) is/are true? Negative feedback is applied in a zero crossing detector circuit. Time constant formula is same for both integrator and differentiator circuit. It is possible to design non-inverting adder circuit. Capacitive reactance decreases as frequency increases. In an oscillator, the oscillation frequency is determined by the tank circuit

Which of the following statement(s) is/are true? Negative feedback is applied in a zero crossing detector circuit. Time constant formula is same for both integrator and differentiator circuit. It is possible to design non-inverting adder circuit. Capacitive reactance decreases as frequency increases. In an oscillator, the oscillation frequency is determined by the tank circuit

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

Q.An integrator converts input signal into ........ waveform. triangular nonf of above square pulse
Given the four statements, which of the following statements are true about an op-amp integrator? i. For an op-amp integrator with R = 100KOhms, C waveform, the output waveform is a cosine waveform. 10UF and a sine wave input %3D ii. For an op-amp integrator with R = 100KOhms, C waveform, thc output waveform is a squarc wave. 10UF and a triangular input %3D %3! iii. For an op-amp integrator with R = 100KOhms, C waveform, the output waveform is a sawtooth waveform. = 10UF and a sine wave input %3D iv. For an op-amp integrator with R 100KOhms, C 10uF and a square wave input waveform, the output waveform is a triangular waveform. Oi, ii, i O i, ii, iv O i iv O ii, ii
Consider Figure 65. Compute for the minimum value of R3 if R₁ = R₂= 51kohms, C₁-C₂-0.001uF and R4=115.07kohms to start the oscillation. R3= kohms +Vcc Op-amp Output sinusoidal signal -VEE S= 4,1 Figure 65 K₂
Vdc please show the circuit in the figure as a Chaotic Oscillator. Show it using one of the simulation programs. You can make any changes you want. m
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be:
Six similar attenuators are used in an audio design and are linked in a cascade. The total attenuation is 80 decibels. The first section of the attenuator circuit has a 20 mV input. Determine (i) the attenuation in decibels provided by each individual attenuation stage, (ii) the output in volts of the final stage (iii) the output in volts of the fifth stage.
6. An AC precision integrator is desired for a particular application to perform the operation: Vo'(t) = -1200 Vi(t) dt The primes indicate the ac portions of the respective functions. The lowest frequency other than a possible de component of the input signal is estimated to be 1.5 kHz. Determine a suitable design. 7. A low frequency differentiator is desired for a particular application n to perform the operation Vo(t) = -0.002 dvi(t)/ dt Based on a periodic signal with a frequency of 1 kHz, determine a suitable design. 8. Design an astable 555 timer circuit to produce 1kHz square wave, where TH = 0.35 ms and T₁ = 0.65 ms. Select C = 0.01 UE, Determine R₁ and Ra. 9. Design a monostable 555 timer circuit to produce an output pulse 5 ms wide. 10. Using op amps with Xsat = +/- 13 V, design a square/ triangular wave function generator circuit to generate 2 kHz triangular wave with a peak-to-peak voltage of 12 V. 11. Design a non inverting Schmitt trigger circuit with VT to be adjustable…
WHAT ARE FREQUENCY DEMODULATORS
if you design differentiator to differentiate input signal varies in frequency between 1 KHz and 20 KHz then find. Cutoff frequency=.......... 01000 O2000 03000 O4000
for the circuit if R = 5ohm, E = 20V and the cut-off (trigger) angle is 90 degrees; Draw the waveform of the source current Is, the output voltage VDC, and the output current Id Calculate the average value of output voltage VDC and output current Id.
Design a differentiator using an op-amp. The output voltage should be a square wave with 5V(peak-to-peak) andthe input voltage should be a triangular wave with10V(peak-to-peak) (1ms).
Which of the following statements is true about an op-amp integrator? For an op-amp integrator with R = 1OOKOhms, C = 10UF and a sine wave input waveform, the output waveform is a cosine waveform. O For an op-amp integrator with R = 100KOhms,C = 10uF and a sine wave input waveform, the output waveform is a triangular waveform. For an op-amp integrator with R = 1OOKOhms, C = 10UF and a sine wave input waveform, the output waveform is a sawtooth waveform. O For an op-amp integrator with R = 100KOhms, C = 10UF and a sine wave input waveform, the output waveform is a square wave. It is the average of the two dc currents that flows into the inverting and non- inverting inputs of an op-amp. Input Bias Current Input Offset Current 03: