Which of the following property the insulating material should possess to resist the flow of current in the cable? O Good Mechanical properties O High insulation resistance properties O High dielectric strength properties O High conductivity properties

Which of the following property the insulating material should possess to resist the flow of current in the cable? O Good Mechanical properties O High insulation resistance properties O High dielectric strength properties O High conductivity properties

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.7MCQ: Consider Figure 3.5. Match the following, those on the left to those on the right. (i) Im (a)...

See similar textbooks

Related questions

Q: 23. What Cable Color-Coding is typically used for the Earth Wire in the Sultanate of Oman? A. BLACK…

A: (A) black wire is used for neutral of ac. (B) where is Blue wire is used for neutral.

Q: In terminating the coaxial cable, if the present procedure is to cut part of the braided shield and…

A: In this question we need to find what is the next procedure is to

Q: What is the smallest square box that will accommodate four No. 12 conductors and four No. 10…

A: conductor A conductor is any piece of material that easily allows heat or electricity to pass…

Q: calculate the current carrying capacity of cable protected by fuse with 60 A ,the first half of the…

Q: 71. A single-core cable has a conductor diameter of 1 cm and insulation thickness of 0-4 cm. If the…

A: Given, A single core cable inner diameter, d1=1 cm=1×10-2 m…

Q: What isolate the gate and the channel in IGFET? Choose the correct answer below: a.thick…

Q: 1. A feeder is made up of three conductors (500 MCM, copper, 75°C rated) that are placed in a…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: Which option from the table4 that best suits for the cable? Justify your selection.…

A: The main purpose of the central conductor is to carry current. Of the 4 given materials as a…

Q: 17. The following drawing illustrates the parts of a shielded cable. The arrow points to the ground…

A: Note: Since you have not specified any question to be answered, as per our honor code, we are…

Q: What is the diameter in inches of a no. 26 AWG wire?

A: 26AWG = 0.0159 inches diameter wire .

Q: list three factors that affect the resistance of conductors

A: The three factors that affect the resistance of conductors are - Length of conductor, l, Area of…

Q: B1 a) List out the properties of insulating materials used for cables. (Any four points)

A: Each core or conductor is in power system provided with a suitable thickness of insulation, the…

Q: 1. A given conductor has a resistance of 1.5 . Find the resistance of another conductor having a…

Q: A cable has 27 strands. Each strand has a diameter of 3 mm. What is the area of the cable in…

Q: Fiber cable sheath is removed by a. Wire Stripper b. Jacket Stripper c. Miller Stripper d. Round…

A: The solution is given Answer is option b

Q: Which layer in the construction of Underground Cables protects the Steel Wire or Tape from…

A: Which layer in the construction of Underground Cables protects the Steel Wire or Tape from…

Q: Name two types of conductor insulation designed to be underground

Q: Name two types of conductor insulation designed to be used underground, and two other types of…

A: Insulator- To prevent unwanted current flow to the ground from its supporting points, an electrical…

Q: central outer conductor- -insulation Figure 6

A: For the domestic electric cable, the conductor must be metal while the insulator must be capable…

Q: Determine the resistance of a 1.25 km long cable composed of 14 strands of similar copper wire…

A: Given : Length of the cable = 1.25 km No. of stands =14 Diameter of each stand =1.3mm we can…

Q: What should be the CPC cable size for a line conductor of sizes up to 16mm² Same size 35 mm2 Half…

A: CPC cable size for the given line conductor of different sizes is given in accordance with table…

Q: 2. With respect to conductors, interpret the following designations: а. THHN b. THWN C. TW d. CU е.…

A: we need to interpret given conductors.

Q: Mention any two factors that can influence the resistance of a metal conductor and explain how each…

A: The factors affecting the resistance of a metal conductor are 1. Conductivity 2. Length of the…

Q: What factors explain the ampacity of the wire

A: The ampacity is defined as the property of the conductor which will carry the maximum amount of the…

Q: 38. The radius of bends in mineral-insulated cable with a %" external diameter shall be not less…

Q: Which of the following is NOT a factor that influence the value of resistance?

A: Answer is option "b" - volume of conductor because, Resistance of a wire, R=ρl/a where ρ is…

Q: A length of square conductor that is 0.25 in. on a side has a resistance of 0.0756 ohm. What will be…

A: Resistance is an electrical property of a material that opposes the flow of electrons or current in…

Q: A 10 AWG copper conductor with type THW insulation is to be run in free air. What is the maximum…

Q: or B.

Q: What ampacity must all branch-circuit conductors used for wiring a ceiling outlet box be de-rated…

A: Dear student as per our guidelines we are supposed to solve only one question .kindly repost other…

Q: 2-Conductors which exhibit similar properties in all conditions are referred to as

A: The explanation is as follows.

Q: What should be the minimum cross-sectional area of each conductor in a two-core cable 100 m long to…

A: Write the expression for the potential difference.

Q: 3. A conductor whose diameter is 0.175 inch has a resistance of 0.5 ohm. The wire is drawn through a…

A: Resistance is the opposition to the flow of current. Its unit is ohm. Formula to calculate…

Q: Making a Conductor thinner but keeping the same length, its resistance. a) Decreases b) Maintains c)…

A: Resistance =ρ×LA =K×1A Where K is constant A is cross section area.

Q: What is the maximum size Grounding Electrode Conductor regardless of the size of the

A: In this we will write about the maximum size Grounding Electrode Conductor regardless of the size of…

Q: Each of the 19 strands of copper cable has a diameter of 59 mils. Calculate the resistance of a mile…

A: According to the question we have to find the value of resistance of a mile of such cable at a…

Q: Consider the three wires below, labelled X, Y. and Z, carrying various currents as indicated.…

Q: 1. What should be the minimum cross-sectional area of each conductor in a two-core cable 100 m long…

A: Referring to the questions, the given data are:

Q: A copper conductor is connected in parallel with twice its length of aluminum conductor. The…

Q: A conductor has a size of 500 MCM, what will be its size in square m?

Q: The resistance of a wire

Q: In Selection of bonding conductor, size of the conductor mainly depends on size of

A: Bonding conductor: It is the conductor that ensures required electrical conductivity.

Q: 1. A wire used for wiring electric ranges, hot water heaters, stoves and hairdryers where both heat…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Give a full presentation on types of insulating materials for cable?

Q: 1. With respect to conductor insulation, interpret the following insulation designations: а. Т b. N…

A: a) T - Wire wrapped in thermoplastic insulation for protection below 32oF to 150oF. b) N - made by…

Concept explainers

Methods of Wiring

Electrical wiring is the way of integrating cables and wires to interconnected equipment such as fuses, switches, sockets, lights, fans, and so on to the main distribution board, which is a specific structure attached to the utility pole that ensures a constant power supply.

Question

Which of the following property the insulating material should possess to resist the flow of current in the cable?
O Good Mechanical properties
O High insulation resistance properties
O High dielectric strength properties
O High conductivity properties

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the cross sectional area of a conductor is doubled, then the resistance of the conductor remains the same. becomes half of the initial value. becomes double the initial value. becomes four times the initial value.
State the main constituent elements of electrical cables, as well as the materials from which they may be made. Describe the following designations: H05VV-U 1G4 mm? and LSXAV 3x16 mm?.
What the need of testing insulators in the laboratory? Why insulators most likely to fail at lower voltage during wet condition as compared to dry condition? What is the importance of test duration in insulation testing?
5. What is the resistance of a copper bus-bar with the dimensions shown figure below.
Two conductors, one of copper and the other of iron, are connected in parallel and carry equalcurrents at 25°C. How many percent of the total current will the copper conductor carry if thetemperature is raised to 100°C? The temperature coefficients of resistance at 0 °C are 0.0043 /°Cand 0.0063 /°C for copper and iron, respectively.
3. The resistance of a conductor having length 1 area of cross section a and resistivity p is given as: a. pa/l b. pl/a c. pla d. /p
The property of insulating material which makes the breakdown voltage high in a cable is ...... Good Mechanical strength O High conductivity O High dielectric strength O High insulation resistance
(A) Explain the difference between series and parallel resistor circuits in terms of (1) the physical connections (2) current & voltage flow. (B) What are the characteristics of a material that obeys ohms law?
10) A certain batch of copper wire was found to have a conductivity of 98% at 20°C. What is its resistivity in un-cm? www
Ferromagnetic materials have this characteristic. A. A relative permeability slightly less than one. B. A relative permeability slightly greater than one. C. A very high resistivity. D. A high relative permeability.
actice Test X SAT Practice Test #3| SAT Sui x O Magnetism Assessment Circuits Assessment Version D X om/formatives/6057e04c0e661559058a72de Maps S Advertisement 8. 9. 10 11 12 13 14 15 16 17 18 19 20 -0-O Into the page Out of the page The wire shown has a current being carried to the right and point P is a distance r away from the wire. By how much would the magnetic field change if the current was doubled and the distance r was doubled? Halved (1/2) Doubled (2x) Quartered (1/4) Quadrupled (4x) No change Search or type URL 12 4. 6 80 R Y U SO F G H. K L. command option O0O000
Assume relative permeability = 1 ..