When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.13 in In segment (2), the normal strain is measured as 1,150 µin./in. Assume L1 = 38 in. and L2 = 90 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar.

When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.13 in In segment (2), the normal strain is measured as 1,150 µin./in. Assume L1 = 38 in. and L2 = 90 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.11P: A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the...

See similar textbooks

Similar questions

An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
The strains for an element of material in plane strain (see figure) are as follows: x = 480 ×10-6. y = 140 × l0-6, and xy = —350 x 10”. Determine the principals strains and maximum shear strains, and show these strains on sketches of properly oriented elements.
A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench and bent around a quarter-circular 90° bend (see figure). The bent section of the pipe is 52 ft long. Determine the maximum compressive strain If the normal strain cannot exceed 6.1 × 10-3 , what is the maximum diameter of the pipe? If d = 4.75 in., what is the minimum acceptable length of the bent section of the pipe?
An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a) Determine the strains for an element oriented at an angle = 250. (b) Find the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
A joint between two glass plates A and B is filled with a flexible epoxy that bonds securely to the glass. The height of the joint is/p = 0.5 in, its length is L = 30 in, and its thickness is/ = 0.5 in. Shear force of I' = 25 kips is applied to the joint. Calculate the displacement of the joint if the shear modulus of elasticity G of the epoxy is 100 ksi. Calculate the average shear strain in the epoxy.
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.17 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ - 45 in. and L₂ - 94 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. P A Answers: L₁ (a) in.₂ = i (b) £₁ = i B (2) L2 in. uin./in.
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.15 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ = 44 in. and L₂ = 82 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. (1) P L₁ B (2) L2
Rigid bar ABCD is supported by two bars. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as -3800 μm/m. Use the dimensions L₁ = 1900 mm, L₂ = 1425.00 mm, a = 190 mm, b = 380 mm, and c=143 mm. Determine: (a) the normal strain in bar (1). (b) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin C before the load is applied. (c) the normal strain in bar (1) if there is a A = 1 mm gap in the connection at pin B before the load is applied. L₁ Answer: (a) &₁ = (b) E₁ = A i i (c) E₁ = i 1 1 1 a B (1) b Rigid bar L2 με με με C (2)