What will be the voltage peaks in the output of the circuit below, if the input is a 40Vp-p sine wave? Note that V1=2V and V2=3V. Consider the threshold voltage of the Silicon diodes used in the circuit. (Answer format is +peak, -peak) O "2.7 V, -3.7 V" O "3.7 V, -2.7V" O "13V, 12V" O "12V, 13V" Rs D₁ V₁ + 46 D₂ V₂ RL

What will be the voltage peaks in the output of the circuit below, if the input is a 40Vp-p sine wave? Note that V1=2V and V2=3V. Consider the threshold voltage of the Silicon diodes used in the circuit. (Answer format is +peak, -peak) O "2.7 V, -3.7 V" O "3.7 V, -2.7V" O "13V, 12V" O "12V, 13V" Rs D₁ V₁ + 46 D₂ V₂ RL

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Calculate the current flowing through the given circuit and the voltage value at the V0 ends. (Threshold voltage = 0.3V for Germanium diodes, Threshold voltage for silicon diodes = 0.6V)
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V. V1=5 V and V2=9 V. R www D1 Vin Vout v1 V2 Maximum voltage of output waveform Minimum voltage of output waveform
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
Problem # 4 In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VpC e. PIV (Peak Inverse Voltage) 10:1 Dy 1ISV ms Ouiput RL 2.2 k2 D, 50 pF All diodes are IN4001. alleee
For the following limiter consider that both zener diodes are identical with Vz = 4.5V @ lz =20mA and rz = 502. Also assume that the zener diodes will have a constant voltage drop of 0.75 V when forward-biased. R Z, Z a) Find the value of R such that the positive and negative limits are +5V when the input reaches ±10V. b) Sketch and label the voltage transfer characteristic for input voltages between ±10 V.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=3 V and V2=8 V. R www D2 DI Vin Vout V2 Maximum voltage of output waveform Minimum voltage of output waveform
Determine the output voltage V out of the circuit shown in Figure. However, when the Zener diode is forward biased, the voltage of both ends is approximated to 0.7V.