Answered: What is the shear stress (in psi) in a…

What is the shear stress (in psi) in a steel sheet (thickness is 0.094 in) of the slug that has the following shape: Note: the press exerts a 320 lb force. 0.98 in 10.25 in 0.25 in 1.5 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A soil sample has a bulk weight of 19.8 kN/m³ at a water content of 20%. Assume G₁ = 2.7 and…

A: The bulk unit weight, γt = 19.8 kNm3 Water content, w = 0.2 The specific gravity, GS = 2.7 To…

Q: A fill having a volume of 15000 m³ is to be constructed at a void ratio of 0.5. The borrow pit solid…

A: Given that :- A fill having a volume of 15000 m3 is to be constructed at a void ratio of 0.5 volume…

Q: *4-60. The bevel gear is subjected to the force F which is caused from contact with another gear.…

Q: An identified source of irrigation water has ion concentrations of Nat, Catt and ++ Mg as 20, 10 and…

A: Given data :- Irrigation water has ion concentrations of Na+=20Ca2+=10 and Mg2+=8 Calculate the SAR…

Q: 4-119. Replace the force system acting on the truss by a resultant force an couple moment at point…

Q: 1. For a uniform bar element (of length, I), determine the element stiffness matrix that operates on…

A: To determine: element stiffness matrix for 3 node axial element.

Q: The readings on staff which is held vertically 60 m from a tacheometer are 1.460 and 2,055. The line…

Q: For the beam shown. Determine the fixed end moment at A and fixed end moment at B. y A →3 ft 60…

Q: 2. Solve for the best choice in terms of utility U=A-0.05X1 -0.02X2 Mode A X2 Car -0.6 30 Jeep -0.3…

A: Given data: Equation for Utility,U=A-0.05X1-0.02X2 and table for Mode Mode A X1 X2 Car -0.6 50…

Q: Calculate the location of maximum deflection using double integration of method

Q: 500 mm Al A 400 kN/m 0.5 m B 40mm 0.5 m Fe с

A: Given data, External dia of two posts = dext = 40mm Distributed load = 400 kN/m Height of…

Q: Determine the elastic curve equation, the slope at B and the deflection at C by double integration…

Q: Q DA V₁ = 1/2 A. Vi V ) B. Vi = - C. VI = V Q V2 Q2 depth, which equ

Q: Using equations of motion in cylindrical coordinates, a. Determine the angle between the extended…

A: Given data: Mass of ball bearing=2 kg Path equation, r=(1.5 θ) m Angular position of arm, θ=π8.t2…

Q: Design a laboratory scale chemostat to aerobically treat a 10 liters per day of a synthetic…

Q: For the built-up section shown, determine the following: a. Centroid of the Area, b. Moment of…

A: Given:

Q: Question 3 The gross commanded area for a distributary is 6000 hectares, 80% of which is culturable…

A: Given data- Gross command area GCA=6000 ha, Culturable irrigable area CIA = 80%, Intensity of…

Q: Q5 A floor system shown in the following figure carries a load of 8 kN/m². There are columns at A,…

A: NOTE: "Since you have posted multiple questions, we will provide the solution only to the first…

Q: 20 KN- 10 kN- For the given figure below. El=constant. Use Slope Deflection Method BE 2 m 2 m 21 I…

Q: Determine the reactions at the supports for the beam shown below. 4 kN/m 10 KN, 4 53m 12 m + 6 m…

Q: A rectangular simply supported beam of size 100 mm × 250 mm size and span 3 m is subjected to a…

Q: For the following data, compute the horizontal distances from the recorded slope lengths AB. You…

Q: 1. Locate the centroid of the shaded figure. Show your solutions and tabulate your data.

A: Given:- To find:- Location of centroid Concept:- In geometry, the centroid of a shape is the…

Q: A rectangular simply supported beam of size 100 mm × 250 mm size and span 3 m is subjected to a…

A: Given Beam Determine the maximum shear stress in the beam.

Q: Time (hrs) 0 12 24 36 48 60 72 84 96 108 Inflow Discharge (m3/hr) 20 191 249 164 110 82 62 48 32 28…

Q: R.L. of point 'A' is 50 m and R.L. of point 'B' is 46.655 m. The distance between AB is 150 m. The…

A: Given :- R.L. of point 'A' = 50 m R.L. of point 'B' = 46.655 m. The distance between AB = 150 m. To…

Q: The level of water in the reservoir is 1.25 m. If there is a rainfall of 38 cm occurring in a month,…

A: Given data- Water level in reservoir = 1.25 m, Rainfall = 38 cm = 0.38 m, Class A pan evaporation=32…

Q: 5.2 An indoor beam shown below is subjected a service live load of 3 kip/ kip/ft dead load in…

Q: Excavation was being carried out for a foundation on plastic clay with a unit weight of 22,5 kN/m³,…

Q: - 1. The hydraulic cylinder gives pin A a constant velocity v 1.6 m/s along its axis for an interval…

Q: An air stream flows over a smooth plate with Reynolds number of 106. The boundary layer can be…

A: Given data, Reynolds number= 106 Boundary layer is turbulent over the entire plate. If length of…

Q: An open circular tank of 30 cm diameter and 150 cm Long contains water upto a height of 80 cm. the…

A: Given that :- N = 300 rpm Diameter = D = 30 cm Radius = R = 15 cm = 0.15 m Calculate the depth of…

Q: (a) Draw qualitatively the deflection curve based on the bending moment diagram. (b) Determine the…

Q: A reservoir has average surface area of 20km². Mean rate of inflow is 10 m²/S mean outflow is 15…

Q: Q-If the spacing between stadia hair and horizontal crosshair in the diaphragm of a tachometer is…

Q: Point A B Northing (ft) 2034.000 1652.332 C 1455.512 D 1293.631 E 1209.869 F 1332.100 A 2034.000…

A: Given: Point Northing(y), ft Easting(x), ft A 2034 1829.593 B 1652.332 1597.877 C 1455.512…

Q: Design a tension member that consists of two C15 channels and two PL 1/2 x 16, arranged as in the…

A: Given data: Two C15 channel sections and two PL 1/2*16 plates Dead load=PD= 300 k Live load=PL= 450…

Q: The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the…

Q: Determine the pressure at point D, in psi.

Q: Select the lightest C section that will safely support the service tensile loads PD= 65 k and PL=…

A: Given:- The service tensile loads PD= 65 k and PL= 50k The length of the column = 14 ft The two…

Q: A 380mm wide by 570 mm effective depth beam carries a uniform ultimate load of 150 kN/m. The beam is…

A: In the given question, the following data is provided: Width of the beam (b): 380 mm Effective…

Q: SITUATION 2: A reinforced concrete cantilever beam has a span of 5m. It supports a factored load of…

A: Span of 5m Factored load of 40kN/m applied 250mm off the centerline of the cross-section of the…

Q: A car has a frontal projected area of 1.6 m² and travels at 60km/hr. It has a drag coefficient of…

A: Given data- Velocity- V=60 km/hr,V=60×518=16.67 m/s,Area A=1.6 m2Drag coefficient CD=0.35,air…

Q: Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the…

A: Given data: h1=0.9 m h1=1.6 m h1=3.9 m Width of the gate, b= m depth of the gate, d=5 m Angle θ=60°…

Q: Convert the following to Back bearing 1. № 89°29'E S 11° 38¹ W 541° 14' E 582⁰361W 589028'E N 1° 33'…

Q: A reservoir has average surface area of 20km². Mean rate of inflow is 10 m²/S mean outflow is 15…

Q: comply with the SSD. 6. A grade g₁ of +3.50% intersects grade g₂ of -2.50% and an equal-tangent…

Q: The capacity of a "28 S type" concrete mixer is 0.8 m³. For mixing one cubic meter of concrete, the…

Q: If length of rod is 2 m and a radius of 20 mm is made of high-strength steel. The rod is subjected…

A: Solution: Given that : Length of rod = 2 m = 2000 mm Radius of rod = 20 mm Diameter of rod = 40 mm…

Q: Wheat is to be grown in the field having value of field capacity equal to 30% and permaner wilting…

A: Given: Field capacity = 30% = 0.3 Permanent wilting point = 15% = 0.15 Dry unit weight of soil,…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Please Asap

What is the shear stress (in psi) in a steel sheet (thickness is 0.094 in) of the slug
that has the following shape: Note: the press exerts a 320 lb force.
0.98 in
10.25 in
0.25 in
1.5 in

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
A steel rod with a cross-sectional area of 188 mm2 is stretched between two fixed points. The tensile load at 23°C is 6,332 N. What will be the stress at -15°C ? Assume a = 11.7 x 10-6 m/(m.°C) and E = 198 GPa. Answer must be in MPa.
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
An aluminium channel section is shown in the figure below: mm 1; mm mm li mm As indicated, the horizontal sides are of length / = 167 mm and thickness 1 - 1 mm while the vertical side is of length l2- 218 mm and thickness 12 - 3 mm. Determine the shear stress in the top side when it is subject to a pure torque of 20 Nm. You may assume that the factor ki may be taken as 0.333. Give your answer in N/mm² to three decimal places.
2. A metal plate is .125 inch thick. What force is required to punch out a square piece 1" x 1"? The ultimate shear stress of the metal is 37,000 psi, and the ultimate tensile stress is 60,000 psi. (2 ntcl Punch Force
Problem: A steel rod with a cross-sectional area of 180 mm2² is stretched between two fixed points. The tensile load at 25°C is 3,600N. Assume thermal coefficient equal to 11.7 x 106 mm/ (mm°C) and E= 200 GPa. a. What is the temperature at which the stress will be zero? b. What is tthe temperature at which the compressive stress will be 48 MPa?
GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
y 400 mm 4 mm B 200 mm A 6 mm The rectangular plate is subjected to the deformation shown by the dashed line. Determine the average shear stress in the plate if the shear modulus of the material is 2 MPa. Express your answer in kPa and round it to the nearest integer if necessary.
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?