What is the maximal length of bit pattern associated with a LFSR with thesame number of outputs as that of figure Q7?(b)(c)State the criteria which must hold for a LFSR to be of maximal length.(d)Show, by using a characteristic polynomial or by any other mcans, that thepseudo-random sequence generated by this circuit is not of maximal length.Describe the operation and purpose of the logic gates labeled A and B in theoperation of the circuit.(e)cikshift registerresetserial inFigure Q7

C) the LFSR is of maximal length if and only if the corresponding feedback polynomial is primitive.…

What is the maximal length of bit pattern associated with a LFSR with the same number of outputs as that of figure Q7? State the criteria which must hold for a LFSR to be of maximal length. Show, by using a characteristic polynomial or by any other means, that the pseudo-random sequence generated by this circuit is not of maximal length. Describe the operation and purpose of the logic gates labeled A and B in the operation of the circuit. cik 6-bit paraliel out chit neilleher

What is the maximal length of bit pattern associated with a LFSR with the same number of outputs as that of figure Q7? State the criteria which must hold for a LFSR to be of maximal length. Show, by using a characteristic polynomial or by any other means, that the pseudo-random sequence generated by this circuit is not of maximal length. Describe the operation and purpose of the logic gates labeled A and B in the operation of the circuit. cik 6-bit paraliel out chit neilleher

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Q5. Design a decoder to convert the 421 BCD codes to drive a 7-segment LEDS that displays the patterns as shown in Figure Q5. Show the design and working steps in implementing your design using NOR gate ONLY in ONE logic diagram. 1 2 3 f off = '0' on = '1' d 4 5 6
5) below is the accuracy table showing the output values for two separate binary number entries (W and Y) with a length of two bits. Get the simplest form of output functions with the Karnaugh diagram. Draw a logic diagram of the circuit that performs the function of these functions.Describe in detail which functions a, b and C perform for 2-bit binary numbers in the input.
d) Draw the schematics of 4-bit synchronous and asynchronous MOD-8 counters and comment on their pros and cons. e) Calculate the noise margin for a logic gate with the following logic levels: VIL = 1.1 V, VIH = 3.2 V, VOL = 0.6 V, VOH = 4.0 V.
We want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) 1/6 Pat DigClock Part List OFFTIME = SuS DSTM1 ONTIME = DELAY= STARTVAL = 0 OPPVAL = 1 Sus EUK FleStim AC Lbrajes Design Cache b) Read the specification of 74LS47 (BCD-to-7-Segment Decoder shown in Appendix) to see how the logic IC operates to drive a 7-segment LED display. Draw the circuit connection of the decade counter in (a) and the decoder to display the count value on the 7-segment LED display. Further explain why common anode…
Design a combinational circuit with four inputs and one output. The output is 1, when the binary value of the input is less than or equal to 3, the output is zero otherwise. The output is 1 when the binary value of the input is a prime number greater than 9.a) Obtain the truth table.b) Find the simplified output function in sum of products. c) Draw the logic diagram using NOR gates only. ……
Derive an equivalent logic circuit of the circuit shown using only all NOR GATES. Determine the number of TTL NOR-gate ICs in the design
(b) For a gated S-R latch. determine the Q output for the inputs in the following Figure. Show it in proper relation to the enable input, also draw the input waveforms on your answer script. Assume that Q starts LOW. EN S R Minimize the combinational logic circuit in the following figure using Karnaugh's map only. Inverters for the complemented variables are not shown. Q2.
1E. Write a VHDL code for all Logic Gates and verify Output waveforms. 2E. Write a VHDL code for Half Adder and verify Output waveforms. 3E. Write a VHDL code for Full Adder and verify Output waveforms.
V dd Q1 Q2 Q5 Q3 A -Output Q4 Q6 Write down the truth table for above logic gate with the ON / OFF status of each MOSFET and identify the gate.
7. Draw the circuit diagram of a 3-bit by 3-bit array multiplier using 1-bit full adder units and basic logic gate. Show where its critical path is in your design.
6. Pass-Transistor Logic Consider the following Pass Transistor Logic (PTL) circuit. (a) Determine the Boolean functions X in Sum-of- Product form. Is this a valid implementation? Give a brief explanation (b) Determine Boolean functions Y in Sum-of- Product form. Is this a valid implementation? Give a brief explanation B A