What is the magnitude and direction of the horizontal component of the resultant hydrostatic force acting on surface ABC? b. What is the magnitude and direction of the vertical component of the resultant hydrostatic force acting on surface ABC? What must be the minimum specific gravity of the cone to keep the hole plugged? a. C.

What is the magnitude and direction of the horizontal component of the resultant hydrostatic force acting on surface ABC? b. What is the magnitude and direction of the vertical component of the resultant hydrostatic force acting on surface ABC? What must be the minimum specific gravity of the cone to keep the hole plugged? a. C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Part B If a 390 N force F1 is applied to the piston with the 4 cm diameter, what is the magnitude of the force F2 that can be resisted by the piston with the 10 cm diameter? F2 10 cm diameter Vertical 2 m F1 4 cm diameter Oil (SG = 0.85) 2.2 m Figure 3: Schematic for task 2-part B.
1. Hydrostatic Force on Plane Surface. An open rectangular tank is 7 m high and has a square base 5 m on a side. If the tank is half-filled with fresh water (density is 1000 kg/m'), determine (a) the total hydrostatic force on a vertical side, in kN and (b) the location of the center of pressure as measured from the liquid surface, in cm. Draw the side view of tank showing the hydrostatic force F and the distance, yp. Is I + Ad a. Magnitude: F = yh,A b.Direction: Perpendicular to the Area c. Location: y, === S.
H.W: A hypodermic syringe contains a medicine with the density of water. The barrel of the syringe has a cross-sectional area (2.50x10-5) m2, and the needle has a cross-sectional area (1.00x10 8 ) m². In the absence of a force on the plunger, the pressure everywhere is 1.00 atm. A force F of magnitude 2.00 N acts on the plunger, making medicine squirt horizontally from the needle. Determine the speed of the medicine as it leaves the needles tip.
H.W2: The tank in Fig. is 40cm wide. Determine the hydrostatic forces on horizontal plan BC and AD? 55 cm 40cm A -10cm 35c Solvent, sg=0.84 Water 25ci 2m Water. 20°C 4m Hg. 20 3m H.W3 water in a tank is pressurized to 85cmHg as show in Fig. Determine the hydrostatic forces per meter width on panel AB? note: Ans: =501 KN
There are various methods that can be used to calculate the hydrostatic force on a submerged surface. Which of the following statements are correct? (i) (iii) The pressure prism method gives good understanding of the fundamentals but it can only be used for plane surface uniform in the spanwise direction. The parallel axis theorem can be used for surface not uniform in the spanwise direction such as a circular or triangular plane surfaces, but it is limited to simple geometry where the second moment of area can be easily defined. The elementary area method can be used for any 2 or 3 dimensional surface as long as the geometric unit normal vector is known at any point on the surface. (A) (B) (C) (D) (i) and (ii) (i) and (iii) (ii) and (iii) All of the above The Eulerian frame of reference is commonly used in analyzing fluid problems instead of the Lagrangian frame of reference. The main differences between these 2 frames of reference are: (i) The steady motion in Lagrangian frame of…
A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 4 inches of carbon tetrachloride (SG=1.59), 2 inches of water and 12 inches of syrup (SG=1.31). The air chamber in the tank is pressurized at 1296 psf. d. Apply the PANEL EQUATIONS to determine the magnitude, direction and location of the total hydrostatic force acting at the bottom of the tank.
A cylinder with a radius of r=1 m is hinged at location A. It is used as a gate to block water in the reservoir with H=6 m a) Determine the horizontal and vertical components of the resultant hydrostatic pressure force acting on the curved surface AB per unit lentgh and its direction. b) For this cylindirical gate, what is the required weight per unit length, to open automatically at H=6 m. water A
2) The tank in the figure shown has a 4-cm diamter plug which will pop out if the hydrostatic force on it reaches 30N. Use Unit Weight of water = 9790 N/m? a) What will be the maximum value of H? b) What will be the reading "h" on the mercury(sg=13.6) manometer? Water H 50° 4-cm dia.plug h 3 сm
M1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged curved surface. Please provide the complete UNITS ANALYSIS, USE OF CORRECT CONVERSION RATIOS and DIAGRAMS in your hand-written solution. INCOMPLETE/NO SOLUTION means NO CREDIT. Encode your FINAL answer in the space provided after each question. A curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m. seawater 0.60 m (SG = 1.03) %3D 0.75 m Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer. Your answer
2)What is the maximum gauge pressure of water that can be measured using a piezometer 2.5 m high? almosphere? (Ans. 24.5 kN/m2)
What height of mercury column is equivalent to 1000 kPa? The density of mercury is 14000 kg/m3.
The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 9810 N/m3. 1 m 3 m 6 m Enter the exact answer. F = i %3D