What are the functions of a Transfer Switch: (Select all answers that apply) Group of answer choices A. Shifts electrical power from the normal utility power source to the standby power source B. Isolates the utility source from the standby source in such a way that there is no feedback from the generator to the utility’s system or vice versa C. When normal power is restored, the automatic transfer switch resets itself and is ready for the next power outage D. Provides for measuring of power usage by the residents during periods of brownouts with the generator offline.

What are the functions of a Transfer Switch: (Select all answers that apply) Group of answer choices A. Shifts electrical power from the normal utility power source to the standby power source B. Isolates the utility source from the standby source in such a way that there is no feedback from the generator to the utility’s system or vice versa C. When normal power is restored, the automatic transfer switch resets itself and is ready for the next power outage D. Provides for measuring of power usage by the residents during periods of brownouts with the generator offline.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter32: Standby Power Systems

Section: Chapter Questions

Problem 5R

See similar textbooks

Similar questions

a. Draw the relationship between excitation current and short circuit, and Please explain. b. At what volts is the alternator end voltage short-circuited? At nominal voltage What will happen if a short circuit is made?
A 10 ohms reactance is connected to a 120 V,60 Hz line. Calculatea. The reactive power absorbed by the reactorb. The apparent power absorbed by the reactorc. The peak power input to the reactord. The peak power output of the reactore. The duration of each positive power pulse
In an On-Off AC Voltage controller, the ON time is 50 cycles and duty cycle is 0.25. The OFF time cycles will be O a. 150 O b. 75 O c. 25 O d. 50
3) 94 select the proper answer for the following: 1) The main processes that have the responsibility of arc initiation in the switching of the high voltage power system are: a) the field and thermal emissions b) the deionization of the arc path c) the photoionization and magnetic field emission 2) The dead tank term is used with: a) Bulk oil circuit breaker b) Minimum oil circuit breaker c) Air blast circuit breaker 3) The errors in the PTs can be minimized by: a) By providing a suitable turn ratio b) By increasing the winding resistance and reactance 2
9. When making a high energy measurement: a. Attach the meter to the energized line first, then to ground. b. Attach the meter to ground first, then to the energized line. c. Attach both meter leads concurrently. d. Remove power completely, attach the meter, then restore power.
explain the operating principle of the hydroelectric power plant
Magnetic Tape Recording Explain briefly the mechanism of Magnetic Tape Recording and how is induced electromagnetism applied in such. Magnetic Levitation (MagLev) Traing Explain briefly the mechanism of Magnetic Levitation (MagLev) Train and how is induced electromagnetism applied in such. Ground Fault Interrupter Explain briefly the mechanism of Ground Fault Interrupter and how is Faraday’s Law applied in such. Induction Stove Explain briefly the mechanism of Induction Stove and how is Faraday’s Law applied in such. Explain short and concise. Thank you.
The fuse in one of the supply phases of a running 3-phase I.M. blows off. Will the motor continue to run at ( i) original speed (ii) reduced speed (iii) come to stand still?
The process diagram of a binary power plant with an ORC-process, utilizing geothermal energy, is presented in figure 1 below. Generator efficiency is 94%, generator output power is 180 kW and evaporator heat power is 2590 kW. Calculate the turbine output power. Round off your answer to one an integer. Heat into process Evaporator Turbine G Feed pump Figure 1. Process diagram of the binary power plant. Generator Condenser
Explain the concept of electrical load shedding and its role in power system management.
Why PMMC Voltmeters can not be used to measure higher voltages directly? a. because the size of the coils will raise b. because the coils will not be present at all c. because of the lesser current ratings. d. because of the lesser size problems
‏What is meant by Excitation Control in a Power System