Water initially at 200 kPa and 300°C is contained in a piston-cylinder device fitted with stops. The water is allowed to cool at constant pressure until it exists as a saturated vapor and the piston rests on the stops. Then the water continues to cool until the pressure is 100 kPa. Water 200 kPa 300°C e Find the overall change in internal energy between the initial and final states per unit mass of water. Use data from the tables. (You must provide an answer before moving on to the next part.) energy is 4 TkJ/kg.

Water initially at 200 kPa and 300°C is contained in a piston-cylinder device fitted with stops. The water is allowed to cool at constant pressure until it exists as a saturated vapor and the piston rests on the stops. Then the water continues to cool until the pressure is 100 kPa. Water 200 kPa 300°C e Find the overall change in internal energy between the initial and final states per unit mass of water. Use data from the tables. (You must provide an answer before moving on to the next part.) energy is 4 TkJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5- During some actual expansion and compression processes in piston cylinder device, the gases have been observed to satisfy the relationship Py" = const.. Calculate: (1) the work done when a gas expands from a state 150 kPa and 0.03 m' to a final volume of 0.2 m for (n=1.3), and (2) show the process on P-V diagram
Question 1 A piston-cylinder assembly with a frictionless piston has a volume of 0.1 m' and initially filled with steam of 0.5 kg at a pressure of 0.4 MPa. There is heat transfer until the temperature reaches 573 K. Find the total heat transfer as well as the work done during the process. Sketch the process on a P-v diagram with respect to the vapour dome.
Steam at 3.5 MPa initially has a temperature of 350C. It was then cooled in an isobaric process until all of it was turned into saturated liquid. Solve for the change in enthalpy.
During processing in a steel mill, a 375kg steel casting at 800 degrees is quenched by plunging it into a 500-gal oil bath, which is initially 75 degrees . After the casting cools and the oil bath warms , what is the final tempertature of the two? The weight per unit volume of the oil is 7.5 lb/gal.
Consider a piston-cylinder device that initially contains water vapor.crowded. Next, heat is added until the pressure and temperature reach1200 kPa and 700°C, respectively, keeping the piston fixed. Then again I add more heat and the temperature rises to 1200°C, and that is when the piston moves,isobarically. Determine:a) The initial pressure of the water vapor, in kPa.b) The total heat transferred to the steam, in kJ/kg
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 300 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.7 m'/kg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
Steam at 1.4 MPa initially has a temperature of 200C. It was then cooled until all of it was turned into saturated liquid. Solve for the change in enthalpy.
Let's consider a closed container. This has a glass sight that allows you to observe the liquid level. The container contains refrigerant 134a at 20 ° C. A dough extraction is carried out from the bottom at a very low rate, the temperature remains constant throughout the process. If the area of the container is 0.05m ^ 2 and after liquid extraction the level drops150 mm, determine the mass of refrigerant that came out. see img
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
.A kilogram of Argon gas( MW= 40 kg/kmol, k=5/3) is in a piston cylinder set-up. Initially, it has pressure of 30kPa and volume of 0.2m3 and expanded to 20 kPa due to heat transfer. If the process is said to be isovolumic, find initial and final temperatures.
A 300 L tank contains gas at a pressure of 3.5 MPa, a Temperature of 30 degrees Celcius, and a mass of 12 kg. A part of the gas was discharged and the temperature pressure change to 20 degrees Celcius and 2 MPa, respectively. The heat was applied and the temperature was back to 30 degrees Celcius. a. Determine the value of the gas constant. b. Determine the final mass. c. Determine the final volume. d. Determine the final pressure.
6. Two kilograms of water is contained in a piston-cylinder loaded with a linear spring and the outside atmosphere. Initial the water is at 200 kPa, and V = 0.2 m³. Heat is now added until the volume grows to 0.8 m³, and the temperature increases to 600°C. Determine the following: (a) Initial phase of the system (calculate quality if appropriate). (b) Find the final pressure of the system. Show how you determine the final state and which table to look for the pressure. (c) Show the process on a P-v diagram and explain why the process is linear.