Water flows into the sink shown in the figure below at a rate of 2 . If the drain is closed, min the water will eventually flow through the overflow drain holes rather than over the edge of the sink. How many 0.4-in.-diameter drain holes are needed to ensure that the water does not overflow the sink? Neglect viscous effects. 1 in. Q = 2 gal/min 0.4-in.-diameter holes Stopper

Water flows into the sink shown in the figure below at a rate of 2 . If the drain is closed, min the water will eventually flow through the overflow drain holes rather than over the edge of the sink. How many 0.4-in.-diameter drain holes are needed to ensure that the water does not overflow the sink? Neglect viscous effects. 1 in. Q = 2 gal/min 0.4-in.-diameter holes Stopper

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The below figure shows a pump that transfers a steady stream of 35◦API crude oil from an oiltanker to a refinery storage tank, both free surfaces being open to the atmosphere. Theeffective length—including fittings—of the commercial steel pipe is 6,000 ft. The dischargeat point 4 is 200 ft above the pump exit, which is level with the free surface of oil in thetanker. However, because of an intervening hill, point 3 is at a higher altitude than point 4.Losses between points 1 and 2 may be ignored.The crude oil has the following properties:Density ρ = 53 lbm/ft 3 ; Viscosity μ = 13.2 cP; Vapour Pressure Pv = 4.0 psia Answer the following questions:1. If the combination of pump and motor is 80% efficient, how much electrical power(kW) is needed to drive the pump?2. If, in order to avoid vapour lock, the pressure in the pipeline must always be above thevapor pressure of the crude oil, what is the maximum permissible elevation of point 3relative to point 4?3. If the flow in the pipeline…
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
Example 2: Water is going to be pumped between point A and B as shown in Figure below. Calculate the maximum h for the flow rate of 90 L/s and pipe diameter of 0.3 m. Hint: minimum total pressure at point B must be above vapor pressure. B 4/1
Use figure below Question : Water at 20 C is to be pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, as shown in the figure. If the pipe is galvanized iron of diameter 7 in and the pump is 75% efficient, what horsepower pump is needed? Neglect minor losses. HINT : pumped through 2300 ft of pipe from reservoir 1 to 2 at a rate of 2.5 ft3/s, & galvanized iron of diameter 7
Question -4: Water at 40 °C is pumped from an open tank through 200 m of 50 mm diameter smooth horizontal pipe as shown in the Fig.4 and discharges into the atmosphere with a velocity of 3 m/s. minor loss are negligible. a) If the efficiency of the pump is 70%, how much power is being supplied to the pump b) What is the NSPHA at the pump inlet? (1) 3 m Diameter = 50 mm, PUMP Length = 200 m Fig.4
A groundwater well with produces 80 m/hr. and has a hydraulic conductivity of 20 m/d. Calculate the following: a. The length of the screen b. The diameter of the delivery pipe. c. The velocity head and the friction losses in the delivery pipe. d. What is the required power of the pump if the abstraction efficiency was 70%? Assume the following: The percentage of the opening in the screen is 17%, the entrance velocity is 1.55 cm/sec, the diameter of the screen is 30 cm, water velocity in the tube is 2.2 m/sec. Assume any missing data.
Water is pumped through a vertical 2-in. new galvanized-iron pipe to an elevated tank on the roof of a building. The pressure on the discharge side of the pump is 200 lb per sq in. What pressure can be expected at a point in the pipe 250 ft above the pump when the flow is 150 gpm? Answer should be: 37 lb per sq. inch Show your handwritten solution, thank you.
The reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3 N*m/N due to friction in the pipes. Point 1 is located at the surface of the water and point 2 is in the free stream of the exit spray. The Distance from the water surface to the free stream is 3 meters. The flowrate for the system is .05 m^3/s (Work on paper required) 1. How much energy is provided to the motor by the flowing water? 2. Assuming the motor has an efficiency rating of 83%, how much power is output? Ar Pressure o water DN 50sch 40 motor r coo ON 80 sch 40
As shown in the figure, the water is directed downward in the installation with a 25 ° angle narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Where the flow is frictionless and gravitational effects are neglected, a) Find the effective pressure at point 2. b) Calculate the x and y components of the force needed to hold the elbow in place and the resultant force. (psu =1000 kg/m3, g = 9.81 m/s2).
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4 ft'/s, as shown in Figure below. The pipe is cast iron of diameter 8 inch. The pump is 80% efficient. (a) Find the velocity and Reynolds number of flow through pipe. (b) Find the head loss due to friction, hf in ft. (c) Compute the pump head, h, in ft and the pump power needed, Ppump in horse power (hp). Given: Density of water, pwater= 1.94 slug/ft'; Viscosity of water, u = 2.05 × 10° slug/ft.s; Friction factor from Moody Chart, f= 0.021. Draw sketch and show all calculations. 180 ft L = 1500 ft, D = 8 in Pump
Water is to be pumped through 1500 ft of pipe from the lower to upper reservoir at a rate of 4 ft'/s, as shown in Figure below. The pipe is cast iron of diameter 8 inch. The pump is 80% efficient. (a) Find the velocity and Reynolds number of flow through pipe. (b) Find the head loss due to friction, h in ft. (c) Compute the pump head, h, in ft and the pump power needed, Ppump in horse power (hp). Given: Density of water, pwater = 1.94 slug/ft'; Viscosity of water, u = 2.05 x 10° slug/ft.s; Friction factor from Moody Chart, f= 0.021. Draw sketch and show all calculations. 180 ft L-1500 ft, D-8 in Pump