Water at 25°C is flowing through a 1.0 km long Gl pipe of 200 mm diameter at the rate of 0.07 m3/s. If value of Darcy friction factor for this pipe is 0.02 and density of water is 1000 kg/ m', the pumping power (in kW) required to maintain the flow is (а) 1.8 (c) 20.5 (b) 17.4 (d) 41.0

Water at 25°C is flowing through a 1.0 km long Gl pipe of 200 mm diameter at the rate of 0.07 m3/s. If value of Darcy friction factor for this pipe is 0.02 and density of water is 1000 kg/ m', the pumping power (in kW) required to maintain the flow is (а) 1.8 (c) 20.5 (b) 17.4 (d) 41.0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An axial-flow pump is designed to deliver water at a rate of 0.90 m3/s running at 620 rpm. Determine the available head, power, diameter and NPSH required for the pump at the maximum efficiency which is 75% . At maximum efficiency, the discharge coefficient, power coefficient, head coefficient and NPSH coefficient are given to be 0.048, 0.0012, 0.018 and 0.023 respectively. Take density of water to be 1000 kg/m3
The water needs of a small farm are to be met by pumping water from a well that can supply water continuously at a rate of 50 L/min. The water level in the well is 13 m below the ground level, and water is to be pumped to the farm by a 2-cm internal diameter pipe. The required length of piping is measured to be 20 m, and the total head loss in the piping system is estimated to be 10 m.a) Using Bernoulli equation, determine the pressure difference between the two points (A & B).
The water needs of a small farm are to be met by pumping water from a well that can supply water continuously at a rate of 50 L/min. The water level in the well is 13 m below the ground level, and water is to be pumped to the farm by a 2-cm internal diameter pipe. The required length of piping is measured to be 20 m, and the total head loss in the piping system is estimated to be 10 m. a) Using Bernoulli equation, determine the pressure difference between the two points (A & B). b) Taking the efficiency of the pump to be 70 percent, determine the rated power of the pump that needs to be purchased.
Three pipes are connected in parallel. The difference in heads in each pipe is 40 m.Pipes Diameter (cm) Length (m) Friction factor1 15 500 0.022 10 450 0.033 20 800 0.0254. If a fourth pipe 25 cm in diameter and length 1100 m with f = 0.018 were attached at the end of the three pipes,what would be the velocity of the water at the fourth pipe?
I need help on this question: According to the question: a) If the pipe connected to the pump inlet has a diameter of 24 mm with length (LCP) of 5 m and Darcy friction factor of 0.03, what would be the actual head rise across the pump for a case where the pump outlet pressure is 200 kPa? The difference in height between pump inlet and outlet is 0.25 m, the tank exit is sharp-edged, and the water level in the tank to the tank exit pipe (HWL) is 2 m. Also, consider that the flow velocity inside the tank is negligible. The value of the actual head rise across the pump is = ? b) What would be the pump motor power if the efficiency is 60%? The value of the pump motor power is = ?
Water from a reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 1 kg/cm2 is maintained at the summit. Water discharge is 30 m above the reservoir. The quantity pumped is 0.5 m3/sec. Frictional losses in the discharge and suction pipe and pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm what amount of energy must be furnished by the pump, kW?
In a pumping system handling water, the surface level of water in the open sanction tank is 3m below the pump centerline and the surface level in the tank is 23m above the pump centerline. The inlet piping ia 7.62cm in diameter has an equivalent of 26m of steel pipe. The discharge line is 6.35cm in diameter has an equivalent lenght of 72m. The pump discharge rate is 12.6 L/s. the friction factor to be 0.024 for both inlet and discharge pipes. Determine: The total head loss due to friction (HL=hfs+hfd) in meters 21.955 3.187 25.142 The total dynamic head in meters 51.142 45.955 49.142 The water power in kW 5.678 6.072 6.319
(b) A storage tank with base area 40 m2 is being filled with water through a duct in which the volumetric flow rate is 12 L/s, as shown in Fig. 3. Water is concurrently being extracted from the storage tank through two exit pipes with cross-section area 150 cm2. The inlet of the exit pipes is located at a certain height, denoted h in Fig. 3, above the bottom of the storage tank. Water is assumed to be inviscid and incompressible. exit pipes Ve 12 L/s k150 cm? K150 cm? 7 m storage tank (base area 40 m2) Figure 3 (i) Determine the flow speed V, in each exit pipe when a constant depth of 7 m is maintained in the storage tank. (ii) If the depth of water in the storage tank is initially 7 m and the flow speed in the exit pipes changes to V. = 2.4 m/s, it takes 1 hour for the water level to coincide with the inlet of the exit pipes. Determine the height h.
.Water is stored in a reservoir 5 m deep and 100 m in diameter. It is pumped through a 0.3 m diameter pipeline at a flow rate of 220 L s1, and the pressure drop due to friction is 1.2 Pa/m. The pump is located at the bottom of the reservoir and has a power of 50 kW and is 70% efficient. How high can the liquid be pumped from the surface of the reservoir up a 30° incline?
Please include a diagram.A pump supplies water at a flow rate of 4ft3/s from an open reservoir through a horizontal 8-in sched 40 pipe. The head loss from the reservoir to the suction of the pump is 2 ft-lbf/lbm, and the discharge is at 90 psig into a 6-in sched 80 pipe. The pump has an efficiency of 65% answer the following:a.) The head that must be delivered by the pump to the water is ________ or energy developed by the pump or output energy of the pumpb.) input energy to the pumpc.) Rated power of the pump in kW
Grape juice is being pumped at 27ºC from an open tank through a sanitary tube (Di = 0.03561 m) for second tank on a higher level. The mass flow rate is 3 kg/s (ρ = 997.1 kg/m³) up to 60 m of linear pipe, with 2 standard 90º elbows (Cff = 1.5) and an angle valve (Cff = 2). the tank supply line maintains a liquid level of 6 m, and the grape juice leaves at a height of 6 m. 24 m above the ground. Calculate the efficiency requirements of the pump that has an efficiency of 65%.
A centrifugal pump(efficiency 86%) lifts water through a total height of 42m from reservoir to discharge. Pumping is through 300m of 75mm diameter pipe at the rate of 20li/s. If pipe friction factor, f = 0.025, what KW is required? Answer: 9