Water at 10 C flows in a 3-cm-diameter pipe at a velocity of 1.5 m/s. The Reynolds number for this flow is ? 34420 QUESTION 2 Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is ? 1.64 QUESTION 3 Consider laminar flow of water in a 0.9-cm-diameter pipe at a rate of 1.25 Lmin. The velocity (m/s) of water halfway between the surface and the center of the pipe is ?

Water at 10 C flows in a 3-cm-diameter pipe at a velocity of 1.5 m/s. The Reynolds number for this flow is ? 34420 QUESTION 2 Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is ? 1.64 QUESTION 3 Consider laminar flow of water in a 0.9-cm-diameter pipe at a rate of 1.25 Lmin. The velocity (m/s) of water halfway between the surface and the center of the pipe is ?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

Water at 303 K is flowing at the rate of 6.3x10-4 m3/s in a pipe having an inside diameter (ID) of 52.5 mm. Calculate the Reynolds number. Density of water at 303 K is 996 kg/m3. Viscosity of water is 0.8 cp.
Water at 10 C flows in a 3.5-cm-diameter pipe at a velocity of 1.75 m/s. The Reynolds number for this flow is ?
To measure the flow rate of water at 20°C in the center of a pipe with an inner diameter of 102.3 mm. pitot tube is used. Manometer reading is 78 mm oil. The Pitot tube coefficient is 0.98. Calculate the velocity at the center and the volumetric flow rate. Density 0.59 g/cm³ for manometer liquid oil, Density of water 1000 kg/m3
What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 2 inches? The viscocity is 1.358 x 10^-5 lb/ft-s and the mass flow rate is 73 lb/h.
The Reynolds number for flow of a certain fluid in a circular tube is specified as 2500. What will be the Reynolds number when the tube diameter is increased by 20% and the fluid velocity is decreased by 40% keeping fluid the same? (a) 1200 (c) 3600 (b) 1800 (d) 200
A tube with 45 meters long, and a diameter of 1.8 meters and 2.3 meters, inlet and outlet respectively. Water is flowing inside the tube. What is the rate of change of the velocity with respect to its length when the inlet has a velocity of 2100 meters/min?Include the ff:correct unitscomplete solution
Oil with density 917 kg/m^3 and viscosity 2.33 kg/m.s flows in a 400 meter long 41-cm-diameter horizontal pipeline at an average velocity of 0.7 m/s. Determine the pumping power required in kW to overcome the pressure losses and to maintain the flow of oil in the pipe. Make sure to check Reynolds number first to identify the type of flow and use the proper equation
Heated air at 1 atm and 100°F is to be transported in a 900-ft-long circular section plastic duct at a rate of 1.4 lb/s. I want to determine the head loss and pumping power at the three diameter values in the table below. Complete the table to help me choose a wise diameter. Why would a good design not only focus on minimizing the pumping power? Diameter Head loss, hi Pumping power, W Reynolds number, Re n.d. f n.d. (in) ft hp 8 12 16
Why are liquids usually transported in circular pipes?
The Flame Consulting Company (FCC) is designing an experiment where theaverage velocity of laminar and turbulent flow must be measured. The velocity profiles for bothlaminar and turbulent flow in a pipe are as follows:Determine the radial location for the average velocity of laminar flow in the pipe. If the problemwere based on turbulent flow the Reynolds Number of 1E5 is used. The value of n is fromd pd x2111CnCu rLaminar flow V Ru rTurbulent flow where n is a function of Reynolds NumberV R           
What are the primary considerations when selecting a flowmeter to measure the flow rate of a fluid?
The rate of flow of water through a cylindrical tube that has an inner radius of 1.2 cm is 2791 cm3 in 88s at 293 K. Determine if the flow laminar or turbulent.