Using the coordinate system shown, determine in kilonewtons the y component of the reaction force at O - Roy
Q: 1. What are the basic types of Air Compressors & how it is differ from each other. 2. What are the d...
A:
Q: A small ship capable of making a speed of 7.0 knots through still water maintains a heading due east...
A: Given Speed = 7 knots Distance = 9.8 nautical miles Time = 1.6 hrs To find Speed Angle from the nort...
Q: Q1: A 4000 Ibm motor is raised from a surface level to 18 ft using an elevator. Calculate the work d...
A: we have to calculate the work interaction
Q: w. How much effort must be applied?
A: To find applied effort.
Q: Example: A hemisphere projection of diameter 0.6 m exists on one of the vertical sides of a tank. If...
A:
Q: Check my we When measuring small pressure differences with a manometer, often one arm of the manomet...
A:
Q: The maximum bending stress at distance 0.5 m from the built-in right hand end in the structural beam...
A:
Q: A radioactive sphere of 20-cm diameter generates heat at the rate of 300 W. It is cooled by placing ...
A:
Q: Let's look back at the Quetsion #4 where one fluid had convection coefficient of 100 150 W/m².K. Let...
A:
Q: What are the different sensors and probes used in aircraft engine
A: Probes are used to collect information and sensors are supposed to perceive the information and gene...
Q: BASED ON ASHRAE STANDARD 62.2, CALCULATE THE FRESH AIR INTAKE TO THE AIR HANDLING UNIT (AHU) THAT S...
A: Given; The number of students, N = 150 watts The volume of the room, V = 30mx65mx3m
Q: Ceel wire is we 140 mm and aressure, find
A:
Q: Which type of driving axle supports the weightof the vehicle?a. Semifloatingb. Three-quarter floatin...
A: Semi-floating type axle: This design contains one wheel support bearing mounted on the outer end of ...
Q: Angle of bite in radian ?
A: Given data; Single pass rolling process; Diameter, d=420 mm Width, b=145 mm Thickness,t=9 mm Thi...
Q: I Review Block A has a weight of 9 lb and block B has a weight of 6 lb. They rest on a surface for w...
A:
Q: The 46-lb load is hoisted by the pulley system and motor M. The motor exerts a constant force of 32 ...
A:
Q: If the Poisson's ratio of an elastic material is 0.8 the ratio of modulus of rigidity to Young's mod...
A: This question is based on the concept of elastic properties of material. Poisson's ratio= 0.8
Q: diameter of a solid steel shaft that will not twist through more than 10 degrees in a 6 m length whe...
A:
Q: F =150 N y 30° P 200 N 350 20°
A: NOTE:- As per our company guidelines we are supposed to answer first 3 sub-parts. Kindly repost othe...
Q: shear center and elastic center.
A: SHEAR CENTRE Shear center is a point on the beam-section where the application o...
Q: Data and Results Vector Magnitude (Dynes, g/s2) Direction F1 F2 F3 Equilibrant (Force table) Resulta...
A:
Q: A hemispherical tank with a diameter of 8 ft is full of water find the work done in ft-lb in pumping...
A:
Q: down about point (A) by Z
A:
Q: o raise and lower the 580-kg bucket i uired to slow the descent of the buch ble.
A:
Q: :1 with an isentropic efficiency of 80% when running at 15000 rpm and inducting air of 293° K. Curve...
A:
Q: 17/ The fertilizer spreader and the fertilizer it contains have a combined mass of 40 kg and a cente...
A: Givenm=140kgC=5mm
Q: 3 - A roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t ...
A: Given Load, P = 175 kN Shear stress = 70 MPa Bending stress = 140 MPa Find Number ...
Q: 33 In a compound helical spring, the inner spring is arranged within and concentric with outer one b...
A:
Q: he principal stresses for a certain state of stress are σ1 = 30 kPa, σ2 = 20 kPa, σ3 = 10 kPa. Find ...
A:
Q: A parachute of hemi-spherical shape allows a parachute jumper of weight 90kg to descend with a stead...
A: A drag force is the resistance created when a body moves through a fluid like water or air. A drag f...
Q: determine the time when the velocity of the elevator will be 3 m/s.
A:
Q: 4. Two and one-half pounds of air actuate a cycle composed of the following processes: polytropic co...
A:
Q: The two wires are connectec at A. If the force P causes point A to be dsplaced horizontally 2 mm, de...
A: To determine the normal strain in each wire.
Q: %o change in diamefesx-?
A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a height;h2...
Q: Water at 25C and a quality of 1% is contained in a spherical tank that has a diameter of .5m. The wa...
A: Given data: Initial Temperature of water = T1 = 25°C =298 KInitial Quality of water = 1%Diameter = ...
Q: Q3: Express the shear and moment functions in terms of x, and then draw the shear and moment diagram...
A:
Q: ghs 3 kg and central sleeve weight is 25 kg. The arms are of 20 cm length and pivoted about axes dis...
A:
Q: +0.040 -0.010 In an interchangeable assembly, shafts of size 25.000-0 'mm mate with holes o +0.030 s...
A: To determine the maximum interference in the assembly.
Q: How many 10-mm-diameter steel bolts can be used on a 600-mm bolt circle coupling so that the shearin...
A:
Q: Situation 3: An 8-m long steel column is pinned at the top and fixed at the bottom. The column is pr...
A:
Q: It is required to insulate a kitchen oven with cork board (k = 0.043 W/mK) so that the heat losses f...
A: Given Data : Thermal Conductivity k = 0.043 W/mK Heat loss Q = 400 W/m2 Inner temperature Ti = 225 ...
Q: One kg of CO2 has a volume of 1 m³ at 100°C. Compute the pressure by (a) Van der Waal's equation (b)...
A:
Q: Air Ta = 0°C D Is Ясоnd A liquid water droplet of diameter D = 255 µm falls on a cold surface with t...
A:
Q: Which invariant reaction can be recognized in the phase diagram shown here? 2500 2300 2100 1900 1700...
A: The correct option in peritectic (option D). The copper-iridium phase diagram is an example of simpl...
Q: apacity.. per person r person through glass, doors a
A:
Q: What is indicated by a LTFT reading of 24 percent?
A: Given Data : LTFT
Q: The controlling force curve of a spring controlled governor is a straight line. The weight of each g...
A:
Q: Two boxes A and B, each having a weight of 160 Ib, sit on the 500-lb conveyor which is free to roll ...
A:
Q: IDENTIFY: A thermodynamic quantity representing the unavi alabliity of a syste'ms therm al enregy cn...
A: The question sentences are not correct and need to be corrected in a meaningful format.
Q: 2.20 .. BIO Blackout? A jet fighter pilot wishes to accelerate from rest at a constant acceleration ...
A: Given: a=5gvs=331 m/sM=3
Step by step
Solved in 2 steps with 2 images
- For the position vectors P and Q shown, determine the orthogonal component of P Ă— Q in the direction of OA.A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2 m 1.2 m 1.2 m 2.8 m |F,| = 6 kN 45° |F| = 5 kN %3D Using the coordinate system shown, determine the components of vector F = Fxi+ F,J+F;k (Answer in Kilo Newtons) F, Choose... + F, Choose... * Fy Choose... + Choose... -4 6 4 e 3.54QA2: Determine the force that hydraulic piston DB exerts on boom ABC, as well as the force exerted on the drive unit at A by boom ABC. Express both forces as Cartesian vectors. The mass of the workers and the utility basket is 250 kg, and the CoG of that mass is directly below point C. [Туре В for LO 3.2, 3.5] 3.5m 35 3.5m A 1m ,drive 2 m unit
- 4. Find the resultant of the concurrent force system shown. 4000 lb 30° 5000 lb 2000 lb 30° 1000 lb 3000 lb4) Use the parallel axis theorem to determine the second moment of mass about the z-axis through the origin for a thin rectangular plate with base b, and height h. Ул ANS. Z 3 [b² + h²] (kg-m^2) h z' bQ3: Resolve F1 into components along the u and v axes and the magnitude of these components.
- A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN 1.2 m 1.2 m 1.2 m 2.8 m |F,| = 6 kN y 45° |F| = 5 kN Using the coordinate system shown, determine the components of vector F = Fxi + F,J+F,k (Answer in Kilo Newtons) Fy Choose. F: Choose.. F. Choose.. Choose... 10.11 -6 -4 3.54A light fixture of negligible mass, has three applied forces acting on it as shown. |F.| = 4 kN %D 1.2 m 1.2 m 1.2 m 2.8 m |F,| = 6 kN %3D 45 |F| = 5 kN %3D Using the coordinate system shown, determine the moment created by the Force F2 about the point 0. M2 = Mxi + M,J + M,k (Answer in Kilo Newton meters) My Choose.. + Mz Choose... + Mx Choose...Find the y-component a force, 100N, acting 40 degrees below the x-axis, *
- The following concurrent forces are acting on a body in xy plane: A 300 lb pointing up to the right 30 degrees with x axis, 400 lb at 45 degrees with x axis acting up to the left, 200 lb down to the left at 60 degrees with x axis, 150 lb down to the right at 75 degrees with x axis and a 100 lb directly to the right. Determine the resultant force and its direction using graphical and analytical method. Pls show the solution, formula and free body diagram.Q1 \ What is the equivalent resultant force of the system acting on the beam below? and where is it located with respect to point O?The following concurrent forces are acting on a body in xy plane: A 300 lb pointing up to the right 30 degrees with x axis, 400 lb at 45 degrees with x axis acting up to the left, 200 lb down to the left at 60 degrees with x axis, 150 lb down to the right at 75 degrees with x axis and a 100 lb directly to the right. Determine the resultant force and its direction using graphical and analytical method. Show solution, formula and the FBD and pls write legible