Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt.The operation is to be started usign a push button. An acknowledgement signal is required when the piston is fully extended. to ensure that the work piece has been tipped onto the belt.The return stroke is to be automatic.Answer using the Solution form provided in the uploaded image. Solution:Component DesignationQuantityNameDesignationCircuit DiagramObservation:Encountered error/s: Problem:Using a double-acting cylinder a work piece is removed andtipped onto a conveyor belt.The operation is to be started using a push button. Anacknowledgement signal is required when the piston is fullyextended, to ensure that the work piece has been tipped ontothe beltThe return stroke is to be automatic.Positional sketch:

Answered: Image /qna-images/answer/adeb7cb6-505a-49b8-8f12-6f42198bfb91.jpg

Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt. The operation is to be started usign a push button. An acknowledgement signal is required when the piston is fully extended. to ensure that the work piece has been tipped onto the belt. The return stroke is to be automatic. Answer using the Solution form provided in the uploaded image.

Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt. The operation is to be started usign a push button. An acknowledgement signal is required when the piston is fully extended. to ensure that the work piece has been tipped onto the belt. The return stroke is to be automatic. Answer using the Solution form provided in the uploaded image.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter4: Drill Press

Section4.2: Tools, Toolholding, And Workholding For The Drill

Problem 12RQ: Which would be the best workholding device for holding a 3/4" 12" 14" flat plate for drilling a...

See similar textbooks

Similar questions

Using a double-acting cylinder a work piece is removed and tipped onto a conveyor belt. Following are the sequence of operations 1. The operation is to be started using a push button (use the label START PB). Include a stop push button (use the label STOP PB) to stop the process at any time. 2. An acknowledgement signal (S1) is required when the piston is fully extended, to ensure that the work piece has been tipped onto the belt. 3. The extension should be slower than the retraction (use a pilot operated check valve) 4. The return stroke should be automatic. a. Design the Electro- Hydraulic Circuit with proper labeling. Include the components required b. Draw the Displacement -step diagram & Displacement -time diagram ( include Cylinder, START PB, STOP PB, DCV)
Electro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing the start pushbutton makes 5 cycles. After making 5 cycles lamp is energized for 3 secs. Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs. Then retract. Cylinder A retract.
USE OF PRESSURE SEQUENCE VALVE! PROBLEM: A double-acting cylinder is to be used to emboss plastic rulers. The cylinder may only extend when the ruler is present and either a push button or a pedal switch is actuated. The return stroke of the cylinder is to occur automatically after the forward end position and the preset pressure have reached.
In the drilling process shown in Figure 2, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation is as follows: Start push button is used to start the process, Cylinder A and Cylinder B clamps the workpiece simultaneously and then drill cylinder lowers the drill and raises afterwards. Once the drill is raised, cylinder A and cylinder B retracts simultaneously. sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B B+ sensors B Figure 2: Drilling Process For the above given drilling process: a) Provide the allocation List for the given application. b) Draw the grafcet and extract the grafcet equation. Obtain the ladder program from the grafcet equations.
2.... Hydraulic controlled riveting assembly machine. hydraulic control system. Must include the following controls: Rotational control of the index table (150 lbs weight). Part clamps at each station . Rivet insertion station (guarded station not clearly shown - assume pick (up/down) and place (forward/return) motion, with rivet gripper control (grip/release). Drill station to attach the rivet. Total cycle should be 10 seconds. how would that schematic look, and how would the speed, forces, and heat loss be calculated. there were no other info given as far as flow rate, torque and things like that. where would you start?
Using a double-acting cylinder a work piece is removed and tipped onto conveyor belt. The operation is to be started using a push button. An acknowledgement signal is required when the piston is fully extended, to ensure that the work piece has been tipped onto the belt. The return stroke is to be automatic. Draw the pneumatic circuit diagram for the problem in this exercise using ISO symbols and connecting the ports with solid lines.
1. In the drilling process shown in Figure 1, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation is as follows: activate the direction control valve to start the process, Cylinder A and Cylinder B clamps the workpiece and then activate the second directional control valve to drill cylinder lowers the drill and raises afterwards. Once the drill is raised, cylinder A and cylinder B retracts. sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B A+ B+ sensors Figure 1: Drilling Process а) Design the Hydraulic Circuit with proper labeling. Include the allocation list and the components required b) Draw the functional diagram/step diagram
Write the sequential procedure and CNC code for making the simple step turning operation for making the shown job - 100 15-1 42 Size of Raw material Total Length = 100 mm, Free length out of Clamping device = 70 mm, Diameter = 42 mm, this has to be reduced to 10 mm, 20 mm, 30 mm, diameter for a length of 15 mm steps each as shown above diagram.
Sketch a typical arrangement of a mechanism of quick return shaping action of power transmission from input of a shaping machine to the output of the tool.
A single cylinder engine is used to drive an irrigation pump. The set-up has the following data: Engine rpm=2200, Pump rpm=1800. Diameter of engine pulley=250 mm, what should the diameter of the second pulley be?
BDS. Do this on раper. 1. Draw a FBD for the cylindrical tub before the metal object is added, clearly labeling all forces. 2. Draw a FBD for the cylindrical tub after the metal object is added, clearly labeling all forces. 3. Draw a FBD for the metal object after it is placed in the tub, clearly labeling all forces. 4. Take a clear photo of the FBDS and upload that here. BIU E E E E МacВook Pro %24 & 4 5 6 7 R Y 00 ト

Q1.With a neat diagram ,explain about the working of Flash Type ADC.