Using 50 ksi steel, select the lightest available section for a beam 8 meters long with lateral bracing at ends and at the midspan. The beam is carrying a uniform dead load of 15 kN/m and a uniform live load of 27 kN/m.The beam also carries a concentrated live load of 32 kN and a concentrated dead load of 28 kN at the midspan. LRFD ONLY.

Using 50 ksi steel, select the lightest available section for a beam 8 meters long with lateral bracing at ends and at the midspan. The beam is carrying a uniform dead load of 15 kN/m and a uniform live load of 27 kN/m.The beam also carries a concentrated live load of 32 kN and a concentrated dead load of 28 kN at the midspan. LRFD ONLY.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.4.5P

See similar textbooks

Similar questions

5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
A built up section of A992 steel, F, = 345 mPa is made from plates fully welded together. The flanges consist of PL16X380 and PL12X500 for the web. Use the NSCP 2015 specifications. PL16x380 WL = 1.5wp %3D A Wu = 3.6wp 10m Which of the following best gives the maximum service dead load, wp? 40.2 kN/m 26.8 kN/m O 10.8 kN/m O 96.6 kN/m PL12x500
Where is/are the location(s) of the maximum compressive flexural stress? A simple I-beam is loaded as shown. 20 mm P KN PKN P KN B 20 mm- B с D L/4 m L/4 m L/4 m Pin support at the NA Midspan at point B Mid span at point D Midspan at the top fiber Roller support at top fiber Section D at the top fiber Section C at +170 mm from the NA L/4 m 20 mm C 250 mm 150 mm 150 mm D A
S f A structure is to be built as shown supporting a uniform load of 18 kN/m. The location for the supports at A and B has been determined. The connection at C may be placed anywhere along the member AD 18 kN/m A C D 3 m B L -7 mi -5 m- If the allowable bending stress for member AD is 8 MPa, which among the choices gives the most economic section? Select the correct response: 275 mm x 550 mm 250 mm x 500 mm 300mm x 600 mm 225 mm x 450 mm rigid
4-1 Figure P4.1 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform ser- vice (unfactored) live load of 1.5 kips/ft. The con- crete strength is 3500 psi, and the yicld strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load and strength- reduction factors from ACI Code Sections 9.2 and 9.3. For the midspan section shown in Fig. P4-1b, compute M, and show that it exceeds Mu- Wo = 14 kips/it plus weight of beam WL - 1.5 kipa/it (a) 20 ft 21.5 in. 24 in. (b) 3 No. 9 bars 12 in. Fig. P4-1
The beam shown has the following properties: steel cover=60mm, f'c=21 MPa, and fy=420 MPa. Determine the ultimate moment capacity of the beam in kN-m. Determine also the type of failure and the beam condition (under-reinforced, over-reinforced or balanced condition) 250mm 2-Ø20mm 3-025mm h = 450mm 50mm
A welded plate girder of 18 m span having flange plates 400x16 mm for each flange and 200x10 mm web. Compute the sectional properties and moment of resistance of the plate girder . Design also the end bearing and intermediate transverse stiffener, if the girder is subjected to U.D.L. of 120 kN/m
An 80-foot long plate girder (see below) is fabricated from a ½-inch x 78-inch web and two 3inch x 22-inch flanges. Continuous lateral support is provided. The steel is A992. The loading consists of a uniform service dead load of 1.0 kip/ft (including the self-weight), a uniform service live load of 2.0 kips/ft, and a concentrated service live load of 500 kips at midspan. Stiffeners are placed at each end and at 4 feet, 16 feet, and 28 feet from each end. Once stiffener is placed at midspan. Determine whether the flexural strength is adequate using LRFD.
3. Design a welded plate girder for a simply supported bridge deck beam with clear span of 20m, subjected to the following: Dead load including self-weight = 20kN/m Imposed load 12 kN/m Two-point loads = 150kN each spaced 2 m apart.
! Required information A 20-mm-diameter rod made of the same material as rods AC and AD in the truss shown was tested to failure and an ultimate load of 150 kN was recorded. Use a factor of safety of 3.0. 1.5 m D В 3 m 3 m 48 kN 48 kN Determine the required diameter of rod AC. The required diameter of rod AC is 31.48 mm.
1. Check the beam shown for compliance with the AISCS. Lateral support is provided only at the ends, and A992 steel (E 345 MPa and Fy= 450 MPa). The only uniform service dead load is the weight of the beam. The 70 KN service loads are 30%DL and 70%LL. Use LRFD. 70 KN 70, KN 70 KN W 14 x 68 0.90m 1.20m 0.90m WI4 x68 IR, R2
The prestress T-beam section has a simple span of 6 m. The tendons is subjected to an initial stress of 900 MPa with an area of 800 mm2. Assuming a loss of stress of 18%, no tension will be acting at the bottom and a maximum stress of 9.5 MPa at the top should not exceeded. -450 100 800 100 -150- Determine the safe moment that the beam could carry based on the allowable stresses. (kN-m)