Under a torsional test for Brass, having a radius of 2.5 mm and a gage length of 72.6 mm, what is the modulus of rigidity knowing that when the specimen at the elastic zone experience a torque of 10 N.m, the angle of twist was 30 degrees? [assume the curve in elastic zone is a straight line passing by the origin] Select one: O a. 394.4 MPa O b. 22.597 GPa c. 79.2 GPa O d. 22597 kPa

Under a torsional test for Brass, having a radius of 2.5 mm and a gage length of 72.6 mm, what is the modulus of rigidity knowing that when the specimen at the elastic zone experience a torque of 10 N.m, the angle of twist was 30 degrees? [assume the curve in elastic zone is a straight line passing by the origin] Select one: O a. 394.4 MPa O b. 22.597 GPa c. 79.2 GPa O d. 22597 kPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a twist test on a specimen of radius 3mm and gauge length 78mm, while the deformation is still elastic the torque was 18,62 Nm when the angle was 1.95 radians. Calculate the modulus of rigidity knowing that: TD = 1 2J %3D 32 21 Select one: O a. 93.57 GPa. O b. 5.85 MPa. Oc 5.85 GPa. Od.9357 MPa. Finish attempt.
In a torsion text, the specimen is a hollow shaft with 40 mm external and 20 mm internal diameter. An applied torque of 2 kNm is found to produce an angular twist of 0.5° measured on a length of 30 cm of the shaft. The Young's modulus of elasticity is 200 GPa. Find the value of..... 1.Modulus of rigidity. 2. Poisson's ratio.
5) A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length having an external diameter of 16mm and a wall thickness of 3mm. The rod and tube are rigidly connected at their ends so that they twist together when a torque of 20 Nm is applied. Galuminum = 30GPA; Gbrass = 40GPA. Determine: %3D a) The values of the torsional stiffness for the rod and the tube b) The torque transmitted by each c) The maximum shear stress in each d) The angle of twist
Q.1. In a creep test, a material with E = 600 MPa is initially loaded with a stress o, = 297 MPa. 1.5 hr after the initial loading, the strain in the material is measured to be 0.12, and after another hour, it is found to be 0.1832. What will be the strain in the material 3 hours after the initial %3D loading? How much time did it take for the strain to reach a value of 0.001?
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 24 mm, and the rod length was 280 mm. When the applied torque reached 255.0 N-m, a shear strain of 1620 microradians was measured in the specimen. What was the angle of twist in the specimen? Answer: i
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
For a steel sample under tensile testing, if the first principal strain was equal to 0.005 and all other principal strain components are zero. If steel has a Lame's constant of 100 MPa and Shear Modulus of 10 MPa. If we plotted the stress-strain curve of this test. What is the area under this curve? Select one: O a. 1500 MPa O b. 1500 kPa 3. O C. 1500 Joule/m O d. 1500 Joule/m O e. NONE
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
in a Torsion test done. the following data were collected: the radius of the specimen was 3mm and the gauge length was 76.2mm. During the elastic zone: T1=0. 01N.m. 81=14.760, 12-17.13N.m, and 02 36.910, The modulus of rigidity G will be equal to: Select one O a 44.283 GPa. O b. 26.522 GPa. O C 462.91 MPa. O d. 12.94 GPa.
In a torsion text, the specimen is a hollow shaft with 40 mm external and 20 mm internal diameter. An applied torque of 2 kNm is found to produce an angular twist of 0.5° measured on a length of 30 cm of the shaft. The Young's modulus of elasticity is 200 GPa. Find the value of (i) Modulus of rigidity. (ii) Poisson's ratio. (iii) Bulk modulus of elasticity.
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 16 mm, and the rod length was 360 mm. When the applied torque reached 254.8 N-m, a shear strain of 1780 microradians was measured in the specimen. What was the angle of twist in the specimen? Part 1 Calculate the shear stress in the specimen. Correct Answer: T= 316.97 eTextbook and Media Part 2 Use Hooke's Law to calculate the shear modulus of the specimen. answer: G= i MPa MPa Attempts: 1 of 5 used
a 200mm long rod with a diameter of 50mm is loaded with a 4kN weight.the rod finale length 201.314mm and finale diameter 42mm.the load at the fracture is 2.5kN and the maximum load is 3.5kN. Calculate to third decimal and determine the folliwing 1.stress 2.strain 3.limit of proportionality 4.percentage of reduction in area 5.percentage elogation