need in 30 mins. I will upvote! Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.875in. and a wall thickness of 0.268 in. Pipe (2) has an outside diameter of 4.500 in. and a wall thickness of 0.229 in. Assume L₁ = 12 ft andL₂= 20 ft. If the normal stress in each steel pipe must be limited to 22 ksi, determine(a) the maximum downward load P that may be applied at flange B.(b) the downward deflection of flange B at the load that you determined in part (a).L2₂L₁Answers:(a) Pmax=(b) VB=(2)(1)MiMkPсBkipsin.

Given Data: Stress in steel, σ =22ksi Young's modulus, E = 30700 ksi For pipe 1: Length of…

Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.875 in. and a wall thickness of 0.268 in. Pipe (2) has an outside diameter of 4.500 in. and a wall thickness of 0.229 in. Assume L₁ - 12 ft and L2= 20 ft. If the normal stress in each steel pipe must be limited to 22 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).

Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.875 in. and a wall thickness of 0.268 in. Pipe (2) has an outside diameter of 4.500 in. and a wall thickness of 0.229 in. Assume L₁ - 12 ft and L2= 20 ft. If the normal stress in each steel pipe must be limited to 22 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
-11 A solid steel bar (G = 11.8 X 106 psi ) of diameter d = 2,0 in. is subjected to torques T = 8.0 kip-in. acting in the directions shown in the figure. Determine the maximum shear, tensile, and compressive stresses in the bar and show these stresses on sketches of properly oriented stress elements. Determine the corresponding maximum strains (shear, tensile, and compressive) in the bar and show these strains on sketches of the deformed elements.
The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the figure b for Problem 7.2-5). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.
The stresses acting on element B on the web of a train rail (see figure part a of Problem 7.2-5) arc found to be 5700 psi in compression in the horizontal direction and 2300 psi in compression in the vertical direction (see figure). Also, shear stresses of magnitude 2500 psi act in the directions shown. Determine the stresses acting on an element oriented at a counterclockwise angle of 50° from the horizontal. Show these stresses on a sketch of an element oriented at this angle.
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
A square steel tube of a length L = 20 ft and width b2= 10.0 in. is hoisted by a crane (see figure). The lube hangs from a pin of diameter d that is held by the cables at points A and B. The cross section is a hollow square with an inner dimension b1= 8.5 in. and outer dimension b2= 10,0 in. The allowable shear stress in the pin is 8,700 psi. and the allowable bearing stress between the pin and the tube is 13,000 psi. Determine the minimum diameter of the pin in order to support the weight of the tube. Note: Disregard the rounded corners of the tube when calculating its weight.
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
An element in pure shear is subjected to stresses ??xy= 3750 psi, as shown in the figure. Using Mohr’s circle, determine the following: (a) The stresses acting on an clement oriented at a slope of 3 on 4 (sec figure). (b) The principal stresses. Show all results on sketches of properly oriented elements.
Acting on the sides of a stress element cut from a bar in uniaxial stress are tensile stresses of 10,000 psi and 5000 psi, as shown in the figure. (a) Determine the angle 0 and the shear stress T and show all stresses on a sketch of the element. (b) Determine the maximum normal stress amaxand the maximum shear stress Tmax in the material.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?