Two pipes A and B which are connected in series have diametersand lengths equal to 400 mm 0200 m, 600 mm 0 300 mrespectively. Water flows in the pipe 300 lit/s. The difference ofelevation between the entrance and exit of the pipe is 5 m.Assume f = 0.02 for all pipes.1.Compute the head loss due to friction.a. 2.57 mc. 3.47 mb. 6.22 md. 3.21 mDetermine the change in pressure between A and B.c. 15.76 kPad. 17.27 kPa2.a.11.54 kPab. 18.21 kPaCompute the equivalent length for a 300 mm Opipe, made ofthe same material.a. 54 mb. 57 mc. 52 md. 59 m3.

Answered: Image /qna-images/answer/5fdff9c4-e8f3-4d92-82c4-8b9c4a4f4863.jpg

Two pipes A and B which are connected in series have diameters and lengths equal to 400 mm 0200 m, 600 mm 0 300 m respectively. Water flows in the pipe 300 lit/s. The difference of elevation between the entrance and exit of the pipe is 5 m. Assume f = 0.02 for all pipes. Compute the head loss due to friction. a. 2.57 m b. 6.22 m 1. c. 3.47 m d. 3.21 m Determine the change in pressure between A and B. a. 11.54 kPa b. 18.21 kPa 2. c. 15.76 kPa d. 17.27 kPa Compute the equivalent length for a 300 mm Qpipe, made of the same material. 3. a. 54 m b. 57 m c. 52 m d. 59 m

Two pipes A and B which are connected in series have diameters and lengths equal to 400 mm 0200 m, 600 mm 0 300 m respectively. Water flows in the pipe 300 lit/s. The difference of elevation between the entrance and exit of the pipe is 5 m. Assume f = 0.02 for all pipes. Compute the head loss due to friction. a. 2.57 m b. 6.22 m 1. c. 3.47 m d. 3.21 m Determine the change in pressure between A and B. a. 11.54 kPa b. 18.21 kPa 2. c. 15.76 kPa d. 17.27 kPa Compute the equivalent length for a 300 mm Qpipe, made of the same material. 3. a. 54 m b. 57 m c. 52 m d. 59 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
A U-tube differential manometer connects two pressure pipes A and B. Pipe A contains carbon tetrachloride having specific gravity 1.594 under a pressure of 117.72 kPa and pipe B contains oil of sp. gr. 0.8 under a pressure of 117.72 kPa. The pipe lies 2.5 m above pipe B. Find the difference of pressure measured by mercury as fluid filling U-tube.A. 120.58. Choose the best answer below: a.31.36 cm of mercury b.25.11 cm of mercury c.64.74 cm of mercury d.13.62 cm of mercury
Three pipes are connected in series. Pipe 1 has length of 850m and diameter of 600mm. Pipe 2 has length of 903m and diameter of 450mm. Pipe 3 has length of 510m and diameter of 350mm. The discharge in pipe 1 is 345 L/s and all pipes has friction factor of 0.021. Determine the diameter of an equivalent single pipe that can replace the three. A) 536 mm B 486 mm с 385 mm D 428 mm E No Answer among the choices
1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
4.5.4. If the pressure difference between points 1 and 2 in Figure P4.5.4 is 25 psi. What will be the flowrate? The pipes are galvanized iron with k, = 0.0005 ft. Take v = 1.06 x 10* ft/s and neglect minor losses. 2000 ft, 8 in dia 10 in dia 2. B 1600 ft, 6 in dia e 800 ft, 10 in dia- Figure P4.5.4
Find the time it takes to decrease the water level in the tank 1 by 1.5m. Use C = 0.60 T. h.. 2.3m do: 300mn * 2m 454 45 Gm
4. Evaluate the pressure at the center of pipe A. Given: y of Liquid 1 = 12 kN/m y of Liquid 2 = 25 kN/m. hi = 60 cm h2 = 10 cm L = 60 cm а. -750 Рa c.-650 Pa b. -800 Pa d. -700 Pa Liquid 1 Liquid 2 h, h2
2. A 20mm diameter commercial steel pipe, 30m long is used to drain an oil tank. Determine the discharge when the oil level in the tank is 3m above the exit of the pipe. Neglect minor losses and assume f = 0.12. D=20mm, L=30 m, f-0.12 3 m
The fluid in the figure is water, with the surface 10m above the datum. The pipe is 15cm in diameter and the head losses are as follows: from 1 to 2, 0m; from 2 to 3, 0.60m; from 3 to 4, 2m; and from 4 to 5, 0.30m. 1.Determine the velocity of flow in the pipe in m/s. 2.Determine the discharge Q in m^3/s. 3.How many centimeters above the center of the pipe will water stand in piezometer tube 3? 4.How many centimeters above the center of the pipe will water stand in piezometer tube 4?
Time: 60 Q1: pump puts 2kw in to the system. Find: b. The pressure in the pipe on section side of the pump (at C). a. Discharge. C 5 kPa L = 200 m 10m ↓ Air Water 55 marks 15 m P L = 50m D = 6 cm f = 0.025 D = 8 cm f = 0.030
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
Water flows from a pressurized tank, through a valve and out a pipe. If Q= 0.1 ft/s, Az 10 ft, P2=0 psig, D = 1lin., ht 5V/2g, please answer the following questions: 1) the pressure in the tank in psig, 2) sketch the EGL of the system., 3) sketch the HGL of the system Air under pressure Water Partly open valve Figure 3. A water tank discharges water through a partly open valve in a pipe with a diameter d