Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The diameter of the larger pulley is ‘3’ m and that of smaller pulley ‘3’ m. The initial tension in the belt when stationary is ‘4’ kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at ‘700’ r.p.m. and length of the belt.

Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The diameter of the larger pulley is ‘3’ m and that of smaller pulley ‘3’ m. The initial tension in the belt when stationary is ‘4’ kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at ‘700’ r.p.m. and length of the belt.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
Two parallel shafts whose centre lines are 4 m apart, are connected by an open belt drive. The diameter of the larger pulley is 1.8 m and that of smaller pulley 3 m. The initial tension in the belt when stationary is 3 kN. The coefficient of friction between the belt and the pulley is 0.3. Calculate the power transmitted, when the smaller pulley rotates at 550 r.p.m. and length of the belt.
Two parallel shafts 5 m apart are connected by open flat belt drive. The diameter of the bigger pulley is 1.5 m and that of the smaller pulley 0.75 m. The initial tension in the belt is 2.5 kN. The mass of the belt is 1.25 kg/m length and coefficient of friction is 0.25. Taking centrifugal tension into account, find the power transmitted, when the smaller pulley rotates at 450 rpm
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
Power is transmitted between two shafts by a V-belt whose mass is 0.9 kg/m length. The maximum permissible tension in the belt is limited to 2.2 kN. The angle of lap is 170° and the groove angle 45°. If the coefficient of friction between the belt and pulleys is 0.17, find : 1. velocity of the belt for maximum power; and 2. power transmitted at this velocity. Note: Sketch the belt drive system for both parts and label the given data on it.
A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5 degree and angle of contact of belt with the pulley is 160 degree. Ifthe mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power.(Consider the centrifugal tension in the belt.)
A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the systemhas a diameter 150 mm and rotates at 200 rev/min. The grove angle is 40° and thecoefficient of friction between the belt and pulley is 0·3.(a) If the maximum tension in any one belt is limited to 800 N and the angle of lap is135°, determine the number of belts required. (b) Determine also, the initial pre-tension required in the belt.
An overhang shaft carry a 900mm diameter pulley, whose center is 250mm from the center of nearest bearing. The weight of the pulley is 600N and the angle of lap is 180°.The pulley is driven by motor horizontally to right it, if the permissible tension in the belt is 2650N and the coefficient of friction between the belt and the pulley surface is 0.3, estimate the diameter of the shaft. Note, Neglect centrifugal tension and assume permissible tensile and shear stresses in the shaft as 84MPA and 68MPa respectively.
3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and pulley is 0.3, semi V-groove angle is 22.5° and angle of contact of belt with the pulley is 160°. If the mass of the belt is 0.45 kg/m and if permissible pull in the belt is 800 N. Calculate the power. Consider the centrifugal tension in the belt.
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.
In an open flat belt drive, a pulley of 800 mm diameter runs at 300 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, the angle of lap is 170° and the maximum tension in the belt is 2000 N. The power transmitted is: 10.5 kW 9.4 kW 8.9 kW 7.6 kW None of the mentioned 13.1 kW
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.