ConstantS | PeriodIC TaiTwo lightweight rods 24 cm in length are mountedperpendicular to an axle and at 180 ° to each other.At the end of each rod is a 480-g mass. The rodsare spaced 42 cm apart along the axle. The axlerotates at 4.7 rad/s. (Figure 1)Part AWhat is the component of the total angular momentum along the axle?Express your answer using two significant figures.画]Lalong axle =kg m?/sFigure1 of 1SubmitRequest Answer480 gPart B24 cmWhat angle does the vector angular momentum make with the axle? [Hint: Remember that the vector angularmomentum must be calculated about the same point for both masses, which could be the cm.]42 cmExpress your answer using two significant figures.480 gΑΣφ24 cm

Given data: Mass of each boll is m = 480 g =0.48 kg Length of…

Two lightweight rods 24 cm in length are mounted perpendicular to an axle and at 180 ° to each other. At the end of each rod is a 480-g mass. The rods are spaced 42 cm apart along the axle. The axle rotates at 4.7 rad/s. (Figure 1) Part A What is the component of the total angular momentum along the axle? Express your answer using two significant figures. Lalong axle = kg m2/s Figure 1 of 1 <> Submit Request Answer 480 g Part B 24 cm What angle does the vector angular momentum make with the axle? [Hint: Remember that the vector angular momentum must be calculated about the same point for both masses, which could be the cm.] 42 cm Express your answer using two significant figures. 480 g να ΑΣφ ? 24 cm

Two lightweight rods 24 cm in length are mounted perpendicular to an axle and at 180 ° to each other. At the end of each rod is a 480-g mass. The rods are spaced 42 cm apart along the axle. The axle rotates at 4.7 rad/s. (Figure 1) Part A What is the component of the total angular momentum along the axle? Express your answer using two significant figures. Lalong axle = kg m2/s Figure 1 of 1 <> Submit Request Answer 480 g Part B 24 cm What angle does the vector angular momentum make with the axle? [Hint: Remember that the vector angular momentum must be calculated about the same point for both masses, which could be the cm.] 42 cm Express your answer using two significant figures. 480 g να ΑΣφ ? 24 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft is rotating at a uniform speed with four masses mı, m2, m3 and m4 of magnitudes 300 kg, 450kg, 360kg and 390 kg respectively. The masses are rotating in the same plane. The corresponding radii of rotation are 200mm, 150mm, 250mm and 300mm. The angles made by these masses with respect to horizontal are 0°, 45º, 120° and 255° respectively. 1) Check the magnitude and position of balance mass if it radius of rotation is 200mm, and 2) Evaluate the effect of adding the balance mass to the system.
The following diagram shows a piston moving in a cylinder with rod AB. Point B is rotating clockwise with an angular velocity of w. cylinder piston A connecting rod crank bearing B ResearchGate The motion of B is given by the equation r = C cos(wt) + Dsin(wt) Were r is the horizontal +vertical distance of B from O, and C, D are constants. For C=D=42mm and w = 20 rad/s. (i) Write r in the form Rcos (wt ± ß) and state the amplitude and period of r. (ii) Sketch one complete cycle of r. (iii) Explore the differences between the derived form and drawn form
Question 27 Notyet an A circular wheel of mass 50 kg and radius 200 mm is rotating at 300 r.p.m. Find its kinetic energy. A- =|三 Enter your answer here....
A solid bar of mass m and length L stands vertically on a frictionless table and is then released to fall down. The moment of inertia about the center of mass is Ic = mL²/12. At the moment when the top end B just reaches the ground (0-0), (a) what are the angular velocity and angular acceleration? (b) what is the center-of-mass acceleration? (c) what is the normal force of the ground to end D? Hint: It may be helpful to find out the instant rotation axis. В m. L D
In a manufacturing process, a large, cylindrical roller is used to flatten material fed beneath it. The diameter of the roller is 7.00 m, and, while being driven into rotation around a fixed axis, its angular position is expressed as 0 = 2.10t? - 0.800r where 0 is in radians and t is in seconds. (a) Find the maximum angular speed of the roller. rad/s (b) What is the maximum tangential speed of a point on the rim of the roller? m/s (c) At what time t should the driving force be removed from the roller so that the roller does not reverse its direction of rotation? |s (d) Through how many rotations has the roller turned between t = 0 and the time found in part (c)? | rotations
A 40-kg disk shown is pin supported at its center. It starts from the rest and rotates to attain an angular velocity of 2 rad/s. The disk is acted upon by a constant couple moment M = 10 N.m clockwise. The spring is originally unstretched and its cord wraps around the rim of the disk. 0.2m ww Ol = a) (10 points) Find the kinetic energy of the disk. b) (30 points) Determine the angle through which the disk rotates
The turning moment diagram for a petrol engine is drawn to the following scales : Turning moment, 1 mm = 5 Nm; crank angle, 1 mm = 1°. The turning moment diagram repeats itself at every half revolution of the engine and the areas above and below the mean turning moment line taken in order are 295, 685, 40, 340, 960, 270 mm. The rotating parts are equivalent to a mass of 36 kg at a radius of gyration of 150 mm. Determine the coefficient of fluctuation of speed when the engine runs at 1800 r.p.m.
A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
The in-plane angular speed of the bent bar indicated below is w = 0.2 rad/s. The dimensions of the bar are L = 0.4 m and H = 0.6 m. Find the magnitude of the velocity (in m/s) of the endpoint B. H B L Figure is from "Engineering Mechanic An Introduction to Dynamics", McGill and King.
A particular bicycle has wheels that are 66 cm in diameter. The radius of the crank armis 18 cm. At its lowest point, the pedal is 16 cm above the ground. A person is pedalingthe bicycle such that the crank arm rotates once every second.Questions:1. Write an equation that models the vertical position of the foot with respect to theground, starting from the lowest point, as the crank arm turns.2. What is the rate of change of the vertical position of the foot when it is at themidline? Explain your answer3. How fast, in kilometres per hour, is the bicycle moving?4. Determine an equation that would model the foot’s position when the cyclist istraveling 5 km/h. Compare this equation to your equation from question 1 andexplain any differences.5. Use calculus to explain why the rotation velocity of a point on the perimeter of awheel is the same as the velocity of the pedal. Use examples to support youranswer.
Gravitational acceleration g = 10 m/s? 1. A uniform thin rod of length Im and mass m,od = 20 Kg in the figure can rotate freely in the plane about an axis at 30 cm from one of its ends while the other end attached with a disk of radius 10 cm and mass maisk = 10 Kg. As the rod swings from the angle 30". a. Find the position center of mass. b. Calculate the moment of inertia for the composed system. c. What is the velocity of the disk while reaching an equilibrium point? 30 cm
The moment of inertia of an aeroplane air screw is 20 kg - m ^ 2 and the speed of rotation is 1000 r.p.m clockwise when viewed from the front. The speed of the flight is 200 km per hour. Find the gyroscopic reaction of the air screw on the aeroplane when it makes a left-handed turn on a path of 150 m radius.