Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring at A has coordinates (0, 0). If a load P acts on the ring at A, the normal strain in AB becomes EAB = 0.02 in/in., and the normal strain in AC becomes €aC = 0.035 in/in. Determine the coordinate position of the ring due to the load. 5 in. 8 in. A

Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring at A has coordinates (0, 0). If a load P acts on the ring at A, the normal strain in AB becomes EAB = 0.02 in/in., and the normal strain in AC becomes €aC = 0.035 in/in. Determine the coordinate position of the ring due to the load. 5 in. 8 in. A

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.6P

See similar textbooks

Similar questions

5. Two bars are used to support a load. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring at A has coordinates (0, 0). If a load P acts on the ring at A, the normal strain in AB becomes EAB = 0.02 in/in., and the normal strain in AC becomes EAC = 0.035 in/in. Determine the coordinate position of the ring due to the load. 60 5 in. 8 in. A P
6. Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ring at A has coordinates (0, 0). If a load is applied to the ring at A, so that it moves it to the coordinate position (0.25 in., -0.73 in.), determine the normal strain in each bar. (Use the figure in Prob.5)
A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight Wis added at C, also hanging from a steel wire CE, then point C is displace down by 0.025in. The cross-sectional area of the wires is 0.002in². The wires are made of a steel alloy with E = 29000ksi and oy = 70ksi. Calculate the strain in both wires, and the weight W. 4₁ B A E Parameter ft L_1 4 L_2 1 L_3 2 L_4 4 C The strain in AB is € AB = The strain in CE is ECE = The weight W = W lb cc 080 BY NO SA 2021 Cathy Zupke D in./in. in./in.
The rigid bar ABC pivots about support B. After application of load P, end C of the rigid bar moves upward by 0.06 in. If the length of bar (1) is L₁ = 51 in, determine the average normal strain in bar (1). Assume that a = 135 in., b=32 in., and c = 0.06 in. 4₁ 1 a Rigid bar B b
F is being held by two cables AB and CB. If the applied force P creates a displacement at point E equal to 3 mm, calculate the strain in cable CB and AB.
A force P of 70 N is applied by a rider to the front hand brake of a bicycle(Pis the resultant of an evenly distributed pressure). As the hand brakepivots at A. a tension T develops in the 460-mm Ions; brake cable (Ae=1.075 mm²), which elongates by δ 6=0.214 mm. Find the normal stress 8and strain e in the brake cable.Brake cable, L = 460 mmHand brake pivot A
Find the forces in all the members of the truss shown in the figure. If all the members have the same cross - sectional area, A, and elastic modulus, E, then identify the member having the maximum magnitude of normal strain. 2 Lb 21 90⁰ 21
The state of strain at the point on the bracket has components Px = 350(10-6), Py = -860(10-6),gxy = 250(10-6). Use the strain transformation equations to determine the equivalent in-plane strains on an element oriented at an angle of u = 45° clockwise from the original position. Sketch the deformed element within the x–y plane due to these strains.
A force P of 70 N is applied by a rider to thefront hand brake of a bicycle (P is the resultant of anevenly distributed pressure). As the hand brake pivots atA, a tension T develops in the 460-mm long brake cable(Ae = 1.075 mm2 ), which elongates by δ = 0.214 mm.Find the normal stress d and strain in the brake cable.
The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied. joint B moves to the coordinate position (0.40 in., -0.55 in.). Assume a - 10 ft, b-7 ft, and h-8 ft. Determine the normal strain in each bar. Answers: EAB Egc i i B P b με με
The rigid body ABC is connected by two links and is exerted by force P as shown aside. If the normal strain in link BE is 0.5x10°, the normal strain in link AD is: -3 D E A 2 m PV 1 m Select one: -3 a. 4.5×10 b. 1.5x10° c. 1.0×10 -3 d. 3.0×10 -3 e. 0.75x10 f. None 3 m 1.5 m.
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.55 in., -0.17 in.). Assume a = 10 ft, b = 20 ft, c = 7 ft, and d = 14 ft. Determine the normal strain in each bar. Answer: EAB || A EBC= i P a (1) y B με με b (2) C d