2. Two 1-mm diameter wires support the rigid bar as shown. Initially, the 300 mm long rigid bar ishorizontal. Determine the value of dimensions a and b so that when the load is applied in thebar, the bar will remain horizontal. After the load is applied using the computed values of a andb, the temperature increases by 15 degrees. What will be the angle of the bar with respect tothe horizontal after the temperature change? Use E = 200 GPa.100 cm75 cmabRigid bar100 N

Since in the question it is given that, the plate is still in the horizontal position after the…

Answered: Two 1-mm diameter wires support the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compound axial member ABC has a uniform diameter of d-2.4 in. Segment (1) is an aluminum [E₁ - 10,000 ksi] alloy and segment (2) is a copper [E₂ - 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ - 78 in. and L₂ - 150 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.35 in. L₁ A Part 1 Aluminum Answer: A- B Save for Later Calculate the cross-sectional area of the compound member. L2 (2) Copper in.² C P Attempts: 0 of 1 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above. Part 3 The parts of this question must be completed in order. This part will be available when you complete the part above.
Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by tightening the two steel bolts. There is no axial load in the assembly at a temperature of 50°F. Find the stress in the steel bolts when the temperature is increased to 200°F. Use the following data: Aluminum cylinder Bronze cylinder Each steel bolt A (in.²) 2.00 3.00 0.75 a (/°F) 12.8 x 10-6 10.5 x 10-6 6.5 x 10-6 E (psi) 10 x 106 12 × 106 29 x 106 1.0 in.- -3 in 4 in.-1.0 in. Aluminum Bronze O
Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine the modulus of elasticity and the modulus of resilience.
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
3. Three bars each made of different materials are connected together and placed between two walls when the temperature is T₁ = 12 degrees Celsius. Determine the force exerted on the rigid supports when the temperature becomes T₂ = 70 degrees Celsius. The material properties and cross-sections are given in the figure. Steel Est = 200 GPa Cst = 12(10-6)/°C Ast = 200 mm2 300 mm Brass Ebr = 100 GPa abr=21(106)/°C Abr = 450 mm² Copper Ecu = 120 GPa acu = 17(10-6)/°C 515 mm² Acu 200 mm- 100 mm
Need asap A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN. If μ = 0.33 and E = 105 GPa. Determine the change in diameter. In mm. Thanks
5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C
The two rods (A-B and B-C) shown in the left panel are connected by pins at A, B, and C. The cross sections of A-B and B-C are 10mm×13mm and 10mm×10mm, respectively. The bilinear stress-strain relation shown in the right panel is for the material used to make the two rods, where Ei is the slope of the stress-strain curve for stresses between 0 and 80 MPa and E2 is the slope for stresses larger than 80 MPa. Note that Hooke's law is only valid for stresses up to 80 MPa. A 1 1 B 0.900 m 3 P = 30 kN 2.44 m C σ MPa 80 E₂ = 40 GPa E₁ = 80 GPa E a) Given the conditions above, find the axial elongation for each rod when subjected to P=30KN. b) Find the final position of Point B due to the applied load P at that location. Hint: Assume point B moves by unknown amounts Ax and Ay from its initial position, and then use right triangles to write the known final lengths of the cables in terms of Ax and Ay. The equations can be simplified by assuming terms Ax² and Ay² are so small they can be…
The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m respectively. The diameters of materials B and A are 2.5 and 3.5 cm respectively. The modulus of elasticity of materials A and B are 250 and 150 GPa respectively. The elongation of the rod is the same for both the materials. A total tensile load of 40 kN is applied to both the materials A and B together. Calculate the load in each material.
7. A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is applied the block deforms into the shape shown by the dashed line. Determine the magnitude of P. The block's material has a modulus of rigidity of G = 26 GPa. Assume that the material does not yield and use small angle analysis. 150 mm - 0.5 mm 150 mm [Ans: P= 260 kN
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: A B T2 N-m 0.4 m 0.1 m 0.3 m T1 N-m The polar moment of inertia of the rod BD is The polar moment of inertia of the tube CA is The maximum shear stress of the rod BD is
The steel bar AB has a x-in.square cross section and is held by pins that are a fixed distance apart and are located at a distance e = 0.034 in. from the geometric axis of the bar. Determine the required distance d for which the bar will just make contact with point C when the temperature increases by 120°F. Use E= 29 × 106 psi and a coefficient of thermal expansion a = 6.5 × 10-6/°F. Use a simple approximation by ignoring the eccentricity during the thermal part of your calculation. (Round the final answer to four decimal places.) in.- B The distance dis 4 in. 4 in. in.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS