To function a hacksaw requires pre-tensioning of the blade. The blade must have a high enough pre-tension that it does not buckle in use, but not so high that the frame becomes permanently deformed (i.e., yields plastically). Determine the maximum blade pre-tension if the frame is not to exceed a yield stress of 48 ksi. b= 0.1875 in X = 0.62510 0.625 in. in. Frame

To function a hacksaw requires pre-tensioning of the blade. The blade must have a high enough pre-tension that it does not buckle in use, but not so high that the frame becomes permanently deformed (i.e., yields plastically). Determine the maximum blade pre-tension if the frame is not to exceed a yield stress of 48 ksi. b= 0.1875 in X = 0.62510 0.625 in. in. Frame

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength ( Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (S) is equal to 0.8Su and endurance Strength (Se) is equal to 0, 5Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S - N diagram
We will use both shearing and bearing analysis to determine the quantities of rivets needed to fasten BC and BE. We can determine two values then choose what will be more safe. ■ For Member BC: ■ Based on Shearing: V T == ■ Av Based on Bearing: P Ab 70MPa = 96000 N .n. (19) ²x n 1/4. π n = 4.84 5 rivets 96000 N (19mm) (6mm) xn 140MPa n = 46.015≈ 7 rivets For member BC, we must use 7 rivets since we must need a minimum of 7 rivets to resist bearing stress produced by the connection. If we only use 5 rivets, then the bearing stress will become 168.42 MPa. It will result to failure since the allowable bearing stress is only 140 Mpa. ■ For member BE: (Practice at Home) Pac EXAMPLE: 5. The figure shows a roof truss and the detail of the riveted connection at joint B. Using allowable stresses of t = 70 MPa and ob= 140 MPa, how many 19-mm diameter rivets are required to fasten member BC to the gusset plate? Member BE? What is the largest average tensile or compressive stress in BC and BE? Say…
The flywheel causes a completely reverse bending on the shaft and the factor of safety is 2, determine: a. The ultimate tensile strength (Su) of the material if the Yield strength (Sy) is 0.6 of Ultimate strength. b. The fatigue life of the shaft given the fatigue strength (Sf) is equal to 0.8 Su and endurance Strength (Se) is equal to 0,5 Su, given the minimum stress is 0.3 of Maximum stress c. Draw the S-N diagram
Answers are already given. Kindly answer all the required forces. ANSWER: FFG=1103.7267 kip, T W= 832. 7498 kip, T Mc= 6272.9979 kip-ft, clockwise Cx= 0 Cy=1297.7498
The head of a 300 mm diameter cylinder vessel will be designed. The internal pressure in the cylinder is Pin = 1MPA. The bolts have initial tightening load of 12 kN. a) Find the stiffness of the bolt and members. b) Determine the number of bolts (N) for a safety factor of 2 for fatique loading. IMPA D= 300 mm M 10 1.5 grade 5.8 cast iron E= 200 GPa Eci= 90 GPa
Q2: A cold drawn steel rod of circular cross- section is subjected to a variable bending moment of 565 N.m to 1130 N-m as the axial load varies from 4500 N to 13 500 N. Determine the required diameter of the rod for a factor of safety 2. Neglect any stress concentration and column effect. Assume the following values: Ultimate strength = 550 MPa %3D Yield strength = 470 MPa Size factor = 0.85 Surface finish factor = 0.89 Correction factors = 1.0 for bending = 0.7 for axial %3D load The endurance limit in reversed bending may be taken as one-half the ultimate strength.
19. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630 in steel wire, which is 10 inches long? Assume deformation to be vertical. Use E = 30 x 106 psi. 4.5 in a. b. 0.0238 0.0431 a. b. 8 mm 3/8 inch Steel wire 25 KN Nixed 20. A pin is used to join the two members shown. If the allowable average shearing stress in the pin is 190 MPa, what is the minimum required diameter for the pin? 2 in. 12 mm C. 0.0581 d. 0.0631 C. d. 10 mm 1/2 inch P 7.5 mm 12 mm 7.5 mm 25 KN
Given a spring with 2.032 mm wire diameter, oil tempered, 8 active coils, OD is 8.5 mm. Determine the free length if the stress will not exceed 820 MPa when spring is compressed solid. Use G = 83 MPa and assume the springs has plain ends. a. 51.6 mm b. 41.6 mm c. 31.6 mm d. 21.6 mm
Q1/ Find the minimum bolt diameter and the minimum thickness of each yoke that will support a load P = 14 kips without exceeding a shearing stress of 12 ksi and a bearing stress of 20 ksi.
5. Determine the strength of a % in bolt having a yield stress of 60 ksi and stress area of 0.1134 in² 283 lbs 823 lbs 238 lbs 382 lbs
Q1 The screw of the shaft straightener exerts a load of 3000Kg. The screw-type is square threaded of outside diameter (7.5cm) and (6mm) pitch. Take the height of the nut (150mm). Determine 1) Force required at the rim of 30cm diameter hand wheel, assuming a coefficient of friction is 0.12. 2) The maximum compressive stress in the screw, bearing pressure on the thread, and shearing stress in the thread. 3) Efficiency of the straightener. Nut T 150 ↓ Hand wheel Screw 100 150- 400 All dimensions in mm
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)