Three liquids given the following properties are poured into the cylindrical container with adiameter of 3 meters and a height of 6 meters.First fluid poured: sg = 1.0 , V = 17.6715 m^3Second fluid poured: sg = 0.81 , V = 10.6029 m^3Third fluid poured: sg = 2.94 , V = 7.0686 m^3Assuming that the container is closed after pouring the fluids and the stable state in thecontainer is reached, determine the pressure at the height of 4-m from the bottom of the tank

(1x17.6715+0.81x10.6029+2.94x7.0686)/(17.6715+10.6029+7.0686) =1.331

Answered: Three liquids given the following…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Liquids A, B and C, in the containers shown, have SG of 0.80, 1.00 and 1.60 respectively. What is the pressure at the bottom of the tank? hA EL. 8 A (SG = EL. 6 B (SG = hc EL. 2 C (SG = EL. 0 a. 86.328 kPa b. 86.382 kPa c. 85.382 kPa O d. 89.328 kPa
A rectangular gate 1.5m long and 0.75m wide is submerged vertically in a tank where the top is 0.5m from the liquid surface, there are 3 liquids Oil,H20,HG each with 0.5m height find the total F and the location from the top using pressure prism Please provide neat solution and use 3 decimal place
Real liquid (y = 10 kN/m³) is flowing laminar in a pipe at a steady rate, but the direction of flow is unknown. Is the liquid moving upward or moving downward in the pipe? If the pipe diameter is 8 mm Elevation = 10 m - --p = 110 kPa and the liquid viscosity is 3.0 x 10-3 N. s/m2 what is the magnitude of the mean velocity in the pipe Elevation =0 m - --p= 200 kPa
Design a rapid mix tank for water at 50° F flowing at Q = 4.0 MGD for a typical process train ina drinking water treatment plant. Use a square tank with a depth 1.25 times the width, a designvelocity gradient G = 900 sec−1, and a hydraulic detention time τ = 30 seconds. Specificallydetermine:a. Rapid mix tank dimensions in feet and inches, to the nearest one inch.b. Input water horsepower (hp).c. Impeller rotational speed if a vane-disc impeller is used having a diameter half of the tankwidth and employing six flat blades and a baffled tank.
The tank contains a liquid having a density of 2.52 slugs/ft^3 10 in 5 ft 10 ft. 7 ft Pliquid 2. 52 slugs/ſt³ %3D a. Determine the unit weight of the liquid when it reaches the indicated level. b. Determine the liquid's weight. Use English units to express your response. c. Assuming no mixing of liquids occur, if glycerin (SG = 1.26) is poured into the tank, will it sink to the bottom, or will it float on the surface of the liquid, or will it be suspended in the liquid?
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.
1. Oil flows through a 200 mm diameter pipe A at 2 m/s and through a 250 mm diameter pipe B at 1 m/s and discharges through a 150 mm diameter pipe C. Specific gravity of oil are 0.9, respectively. a) Determine the discharge at pipe C. b) If alcohol flows through pipe B. Determine the average density of the two fluids as the mixture flows through the pipe at C. Specific gravity of alcohol is 0.78. B ↑
A container holds two layers of different liquids, one fluid having a specific gravity of 1.1 is 30cm deep and the other fluid having a specific gravity of 1.6 is 40cm deep. A solid cubical metal having an edge dimension of 18cm and specific gravity of 6.5 is submerged such a manner that half of the cube is on the top layer and the other half in the bottom layer of fluids with the square base of the cube horizontal. Help me compute the weight WCUBE of the cubical metal in newtons, compute the buoyant force BFCUBE in newtons acting on the metal object, and compute the tension T in newtons in the wire holding the cube to maintain its position. please draw a figure
Tow oil tanks are connected with a pip that has a constant radius, the readings of the two gauges and the elevations are as follow; p1 p2 z1 z2 Oil SG psi psi (ft) (ft) 40.4 95.7 56.8 68.2 0.8 Determine and justify the flow direction of oil in the pipe 2. 1.
There are four liquids that are to be poured in a single vessel that is located in an atmosphere with g = 3.72m/s2. The first liquid is seawater (SG=1.025), the second is kerosene (ρ=1.591 slugs/ft3), the third is castor oil (SG=0.959), and the last liquid is liquid butane (unit weight = 2235.72N/m3 @ g=3.72m/s2). (a)Determine the density of seawater, the specific gravity of kerosene, the unit weight of castor oil and the density of liquid butane expressing all your answers in SI Units. (b) Illustrate the order of the liquids from the top-to-bottom of the vessel?
1. A block, 1ft square and 9 inches deep floats on a stratified liquid composed of a 6in layer of water above a layer of mercury. Determine the weight of the block if the position of its bottom is 1 inch below the mercury. 2. At point A in a pipeline carrying water, the diameter is 1m, the pressure is 98kPa and the velocity is 1m/s. At point B, 2m lower than A, the diameter is 0.5m and the pressure is 20kPa. Determine the direction of flow. Show detailed computation. 3. What is the hydraulic radius of the channel shown: 1.5m 1.5h 4. wty A vertical right-angled triangular surface has a vertex in the free surface of a liquid. Find the force on one side. 1.5m 1:2m

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS