Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angle of 15° ohms, calculate the currrent flowing in each impedance. Use Nodal analysis.

Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angle of 15° ohms, calculate the currrent flowing in each impedance. Use Nodal analysis.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

what us the resistance of teb 240- resistors connected in series? in parallel?
Determine the DC currents (IB, Ic and lĘ) and dc junction voltages (VBE, VCE and VCB) Ig=Blank 1 mA, Ic=Blank 2 mA, IĘ=Blank 3 mA, VBE= Blank 4 V, VCE = Blank 5 V and VCB = Blank 6 V Use 2 decimal places. Use the following values: VBB = 2V RB = 7 kQ Rc = 248 Q Vcc = 19 V BDc = 56 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer Blank 4 Add your answer Blank 5 Add your answer Blank 6 Add your answer
What will be the value of the twiddle factor: W42
Based on Figures la,1b and 1c and RLC elements, write a discussion on voltage-current relations and power factor. Im A Im A Im A V Re Re Re Figure la. Figure 1b. Figure 1c.
If T = 0.6Z – 60° and A = 48cm find the position of the first voltage minimum on the line. Select one: O a. The first voltage minimum is at 2cm from the load. O b. The first voltage minimum is at 72cm from the load. O c. The first voltage minimum is at 8cm from the load. O d. The first voltage minimum is at –4cm from the load. O e. The first voltage minimum is at 20cm from the load. O f. The first voltage minimum is at 32cm from the load. O g. The first voltage minimum is at 44cm from the load. O h. The first voltage minimum is at 24cm from the load.
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
In a series AC resistive circuit: a) voltage leads current by 90°(degrees). O b) current leads voltage by 90°(degrees). © current and voltage are in phase. d) d current and voltage cancel.
The generator convert from PV to PQ if the active power of the generator exceed the * maxinum and minimum limits between the maximum and mimium limit equal to the load power O Non of them
If the voltage V, = 800 mV, then the current flowing in the load I, is: %3D -j20n Select one: O a. None of these O b. Is 100 <-90° mA O c. Is 5.0<.-90° A O d. Is 5 <90° mA ell
For a certain power shpply, the no load and full load voltage are 22 V and 18 V respectively. What will be the load regulation?
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). Choices: 0.11A 22mA to 89mA 9A 0.11A to 9A Plss show complete solution
Determine the loop currents Ia, I,, and Ic. 100 Ic 100 100 100 100 Ib 55V 100 V la