Three impedance each 10+j 5 ohms connected in the delta on a balanced three-phase source. If the equation of phase voltage is Van= 120 sin wt. What is the equation of the current through the impedance connected across phases a and b? O a. 18.59 sin(wt+3.44 degree) O c. 21.32 sin(wt-8.15 degree) O b. 20.02 sin (wt-22 degree) Amp

Three impedance each 10+j 5 ohms connected in the delta on a balanced three-phase source. If the equation of phase voltage is Van= 120 sin wt. What is the equation of the current through the impedance connected across phases a and b? O a. 18.59 sin(wt+3.44 degree) O c. 21.32 sin(wt-8.15 degree) O b. 20.02 sin (wt-22 degree) Amp

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
The phase b voltage and the phase b current of a balance three-phase system are V = 220 sin (wt + 210°) and I = 10 sin (wt-180°). * A. 5256.44 W B. 5514.38 W C. 5715.76 W D. 6049.22 W
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
The values of the elements for the given circuit are given below.The maximum average power that can be transferred to the ZL load iswhich one?R1 = 400 OhmsL = 1000j OhmsR2 = 500 Ohms
The voltage across a load is Vt : 104/2 cos(wt +75°), and the current through the load is ¡(t) = 2/2 cos(wt + 30°). The reference direction for the current points into the positive reference for the voltage. Determine the complex power and if this load is inductive or capacitive? S = 14140 + jl14140 Inductive S = 40000Z45° %3D Сараcitive S = 2000Z105° Сараcitive S = 5000 – j5000 Inductive
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM
Impedances Z2 and Z3 in parallel are in series with impedance Z1 across a 100 V, 50 Hz ac supply. Z1 =6.25 + j1.25 ohm; Z2 = 5+ j0 ohm and Z3 = 5-jXc ohm. Determine the value of capacitance of Xc such that the total curent of the circuit will be in phase with the total voltage. When is then the circuit current and power.
lši vl pir:10 Expert Q&A + 1. For the circuit in Figure: a. Determine I, VR, and Ve in phasor form. b. Calculate the total power factor, and indicate whether it is leading or lagging. c. Calculate the average power delivered to the circuit. d. Draw the impedance diagram. e. Find the voltages VR and Vcusing the voltage divider rule and compare them with the results of part(a) above. + Uc - + Ug - 30 2 L = 0.2 H L =0.2 H C = 4 µF e = V2(20) sin(377t + 40°) Expert Answer Home Search More II
Three-phase supply from utility The diagram shown in figure has two three- phase loads that form part of a manufacturing plant. They are connected in parallel and require 4.16 kV rms. Load 1 is 1.5 MVA, 0.75 lag pf A connected. Load 2 is 2 MW, 0.8 lagging pf, Y connected. The feeder from the power utility's substation transformer has an impedance of 0.4+j0.8 2/phase. Deter- mine the following: (a) The required magnitude of the line voltage at the supply. (b) The real power drawn from the supply. (c) The percentage of the real power drawn from the supply that is consumed by the loads. 0.4 Ω j 0.8 Ω 0.4 Ω j 0.8 Ω 0.4 Ω j 0.8 Ω m Load 1 am Load 2
Two alternating voltages are represented by vị = 50 sin wt volts and v2 = 100 sin(wt - -). Draw the phasor diagram and find by calculations a sinusoidal expression to represent vi and v,. www The instantane ous values of two alternating currents are given by i = 20 sin wt and i, = 10 sin (wt + ) A. Find the sinusoidal expression for (i1 + i2) by drawing phasors and by calculations.