thin layer oI water flowWs down a plate inclined to the horizontal with an angle a = 15° in the shown coordinate system. If the thickness of the water layer is a=0.5 mm, assuming that the flow is laminar and incompressible, (water density p = 1000 kg/m³viscosity u = 0.001 Pa.s and acceleration of gravity g = 9.81 m/s²) and an air flow shears the layer in a direction opposite to its flow with a shear stress of 1 N/m². Solve the Navier-Stokes equation: %3D air

thin layer oI water flowWs down a plate inclined to the horizontal with an angle a = 15° in the shown coordinate system. If the thickness of the water layer is a=0.5 mm, assuming that the flow is laminar and incompressible, (water density p = 1000 kg/m³viscosity u = 0.001 Pa.s and acceleration of gravity g = 9.81 m/s²) and an air flow shears the layer in a direction opposite to its flow with a shear stress of 1 N/m². Solve the Navier-Stokes equation: %3D air

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The slope of the height h of a surface wave moving in a shallow pool of liquid is related to the speed of the wave u and gravity g by the following equation и ди дх g əx (a) Use a length scale L and a velocity scale Vo to 'nondimensionalize' the equation (b) What is the nondimensional parameter of the flow?
Figure shows the flow of water over a dam. Thevolume fl ow Q is known to depend only on crest width B ,acceleration of gravity g , and upstream water height Habove the dam crest. It is further known that Q is proportionalto B . What is the form of the only possible dimensionallyhomogeneous relation for this flow rate?
The Reynolds transport theorem (RTT) is discussed in Chap. 4 of your textbook. For the general case of a moving and/or deforming control volume, we write the RTT as follows: d pb dV + pbV-ñ dA dt dt dB sys where Vr is the relative velocity, i.e., the velocity of the fluid relative to the control surface. Write the primary dimensions of each additive term in the equation and verify that the equation is dimensionally homogeneous. Show all your work. (Hint: Since B can be any property of the flow-scalar, vector, or even tensor—it can have a variety of dimensions. So, just let the dimensions of B be those of B itself, {B}. Also, b is defined as B per unit mass.)
d²u dy² pg where g is the acceleration due to gravity H
U L CD Fig.1. Airflow on a cylinder U U U/2 L/2 L/2 1. When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created downstream, idealized as a V shape in Fig. 1. Pressures p1 and p2 are approximately equal. (a) If the flow is two-dimensional and incompressible, with width b into the paper, derive a formula for the drag force F on the cylinder. (b) Rewrite your result in the form of a dimensionless drag coefficient based on body length F pU²bL
Ex. The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N, Assuming that the viscosity resistance due to water and air is negligible in comparison with the wave resistance, calculate the corresponding speed of the prototype for dynamically similar conditions. What would be the force required to propel the prptype at that velocity in the same lake? Ans.: 10.95m/s, 13500N
Mott ." cometer, which we can analyze later in Chap. 7. A small ball of diameter D and density p, falls through a tube of test liquid (p. µ). The fall velocity V is calculated by the time to fall a measured distance. The formula for calculating the viscosity of the fluid is discusses a simple falling-ball vis- (Po – p)gD² 18 V This result is limited by the requirement that the Reynolds number (pVD/u) be less than 1.0. Suppose a steel ball (SG = 7.87) of diameter 2.2 mm falls in SAE 25W oil (SG = 0.88) at 20°C. The measured fall velocity is 8.4 cm/s. (a) What is the viscosity of the oil, in kg/m-s? (b) Is the Reynolds num- ber small enough for a valid estimate?
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
Consider laminar flow through a long section of pipe, as in Fig. For laminar flow it turns out that wall roughness is not a relevant parameter unless ? is very large. The volume flow rate V· through the pipe is a function of pipe diameter D, fluid viscosity ? , and axial pressure gradient dP/dx. If pipe diameter is doubled, all else being equal, by what factor will volume flow rate increase? Use dimensional analysis.
Fluid Mechanics. Fluid kinematics. The figure below represents the upper view of pillars, with circular sections of 0.5 m, which support a bridge. The figure also shows the river speeds before and after reaching the pillars. The width of the bridge is 2d. *Consider that in the symmetry section of the bridge there is no flow and the slightest force is exerted in the cross section. d Uniform speed (v) = 2 m/s d' fo) = 15 + V = = 1,5 +: Whereas d = 2 m and d' 1 m, determine: a) What possible control volumes could be used to resolve the issue? b) The flow rate per unit of length entering the plane of the image. c) The slightest force exerted by the river water in this pillar of the figure. d) Are there any generated momentum? If so, justify it.
In an experiment to determine the force acting on an oval-shaped body, a model is mounted in the test section of a wind tunnel. The test section itself has rectangular cross section with height 2h and width l (into the page). The model spans the entire width of the test section. The model is subject to a steady, uniform, incompressible flow of velocity V₁. The pressure gauge indicates a pressure difference (Ap) between the test section exit (location 2) and the test section entrance (location 1). The velocity profile downstream of the model is shown in the figure. Use the control volume shown. Find the force acting on the model in terms of given quantities V₁, h, l, Ap, and density, p. Ap V AL
P1.10 The Stokes-Oseen formula [18] for drag force F on a sphere of diameter D in a fluid stream of low velocity V, density p, and viscosity u, is F = 3TµDV + 16PD? pVD Is this formula dimensionally homogeneous?