These are Otto cycle characteristics: * The working fuel is used as Petrol Fuel injector is used for igniting the charge System is light in weight Engine starting is easy in cold weather Only air is entering during suction stroke Considered as not high speed engine Low compression ratio Mixture of air fuel is entered in suction stroke It is called as constant pressure cycle Low thermal efficiency

These are Otto cycle characteristics: * The working fuel is used as Petrol Fuel injector is used for igniting the charge System is light in weight Engine starting is easy in cold weather Only air is entering during suction stroke Considered as not high speed engine Low compression ratio Mixture of air fuel is entered in suction stroke It is called as constant pressure cycle Low thermal efficiency

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter9: Automotive Engine Designs And Diagnosis

Section: Chapter Questions

Problem 15RQ: Which of the following is an expression of how much of the heat formed during the combustion process...

See similar textbooks

Similar questions

These are Diesel cycle characteristics: * Low thermal efficiency Considered as not high speed engine System is light in weight Mixture of air fuel is entered in suction stroke Low compression ratio It is called as constant pressure cycle Fuel injector is used for igniting the charge Engine starting is easy in cold weather The working fuel is used as Petrol Only air is entering during suction stroke
Auto-ignition might occurs in spark ignition .4 engine at low engine speed because the flame velocity is slow and thus the burn time is long, this results in more time for .auto-ignition .True False O Spark ignition engine with high.5 compression ratio can be used with less possibility of auto-ignition by Increasing the inlet temperature Using low octane number fuel O Using high octane number fuel O Reducing the turbulence motion None of the above Cross-flow (in four stroke engine) from .6 cinlet to exhaust occurs the end of the exhaust stroke and the beginning of the induction stroke when O both valves are close the end of the exhaust stroke and the beginning of the induction stroke when O both valves are open At the end of the intake stroke and the beginning of the exhaust stroke when O both valves are open the end of the exhaust stroke and the beginning of the compression stroke O when both valves are open
Using the diagram, explain the Two-stroke Cycle Engine. Spark plug wwwwwww Piston Reed valve Intake port Air-fuel inlet Combustion chamber Exhaust port Air-fuel mixture
Which of the following is not one of the strokes of a four-cycle engine? Compression Exhaust Intake Ignition
What defines the combustion chamber of afour-stroke engine?
What is specific fuel consumption of an engine?
C- Fill the blank 1- Internal combustion engines classified according to air intake into the cylinder to and-- 2- Typical compression ratio for modern gasoline engine lie between 3- There are a number of gasoline additives that are used to raise the octane number such as 4- Higher compression ratio in SI engine lead to 5- The thermal efficiency of CI engine is than of SI engine. 6- Fuel with octane number of 78 indicate 78%- -and 22%- 7- Anti-Knock quality improves with - no. of carbon atoms. 8- Higher compression ratio in SI engine lead to 9- Maximum power overtaking a vehicle or climbing up a hill (extra load) this requires a mixture.
engine and why? 04/ Write a notes on heat balance sheet, draw that on the energy flow and enhance your answers with equations. Quiz a were recorded during a test on a smgo Feder four stroke oi enoine
How do the volumetric efficiency and air-fuel ratio change as the engine's rotational speed changes? With a brief explanation of the change process with an explanation of the reasons
discuss the Compression-ignition engine its parts and functions
There can be more than 1 answer per item What is the purpose of having piston ring gaps?So that the temperature from the piston can be easily transferred to the cylinder wallsFor easier overhaul proceduresSo that the piston rings will have allowance in the event of thermal expansionSo that oil can freely enter the system The ideal prototype of the spark-ignition engines, constant volume combustion.Diesel cycleOtto cycleBrayton cycleCarnot cycle
List three alternative fuels for an internal combustion engine and briefly explain where they come from.