The voltage source, V, in the RC circuit has been at 0 Vfor a long time and then goes to 1 V at t = 0 as shown.R = 1.2 kn and C = 0.1 μF.VsC.+1RC+Vo-Voltage (V)H0.80.60.40.20-0.10Voltage Source, Vs0.10.2Time (ms)a. Calculate the circuit's time constant in us.b. Find the expression that describes the capacitor voltage, v, as a function of time, t.What is the voltage on the capacitor when t-100 us?0.30.40.5

The voltage source, Vs, in the RC circuit has been at 0 V for a long time and then goes to 1 V at t = 0 as shown. R = 1.2 kn and C= = 0.1 µF. + a. R www + Calculate the circuit's time constant in us. b. Find the expression that describes the capacitor voltage, C. What is the voltage on the capacitor when t-100 us? Voltage (V) 1.2 1 0.8 0.4 0.2 0 -0.1 0 Voltage Source, Vs 0.1 0.2 Time (ms) as a function of time, t. 0.3 0.4 0.5

The voltage source, Vs, in the RC circuit has been at 0 V for a long time and then goes to 1 V at t = 0 as shown. R = 1.2 kn and C= = 0.1 µF. + a. R www + Calculate the circuit's time constant in us. b. Find the expression that describes the capacitor voltage, C. What is the voltage on the capacitor when t-100 us? Voltage (V) 1.2 1 0.8 0.4 0.2 0 -0.1 0 Voltage Source, Vs 0.1 0.2 Time (ms) as a function of time, t. 0.3 0.4 0.5

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

At 0-, no currrent flows through the capacitors because they are open, how did you combine the capacitors for the voltage divider since it is the capacitance value and not reactance, is it right? Can we just combine the capacitance value? Please explain. I did not understand..
For the network shown in Figure (Q5), Find: 1. The total equivalent inductance (Lequiv.). 2. If the current waveform shown in Figure (6) is applied to the (Leguiv). Determine an expression for the voltage across it. 6H 10 H 9H 4H SH 3 H 20 H 13H Lequiv. Figure (Q5) i (A) - (ms) 10 12 -5- Figure (6)
Required information Problem 06.037 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS The current through a 17-mH inductor is 4 sin 100t A. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Problem 06.037.a - Voltage across an inductor Find the voltage vt). The voltage is cos 100t V.
3. A 10ohms resistor and an unknown inductance is connected in series. The series combination is then connected to a 10V DC source. After 1 sec the voltage measured across the inductor is 3V. Find the value the unknown inductance for this condition. Use the false- position method to determine L to a level of Es = 0.1%. Employ initial guess of x₁ = 6 and x₂ = 10
Given circuit, capacitor voltage is at 0 V with switch SW1 open. At time t0, switch SW1 is closed. At time t0, what is the voltage v? What is the voltage v at time infinity? At time t0, what is the current through R2? What is the current through R2 at time infinity?
a) The voltage across a 20uF capacitance is v. = 50 sin( at - 80) volts and Frequency equal to 100 Hz. Determine the current through the capacitor i and sketch its waveform. b) Define phasor
An emf source with E=100 V, a resistor with R=80 ohms, and a capacitance with C=4 uF are in series.connected. While the current is 0.9A during the loading of the capacitor, the load on the plates of the capacitor ishow big is it (in uC)?
Calculate capacitance Cand voltage U over resistance. What is the peak value of resistance's voltage? Voltage source e(t) = ésin(wt + 45°). Resistance R-50, circuit's total reactance X-50, inductance L =50mH, ê -40V and frequency f =50Hz. R L Give the answers to one decimal place. Do not write numbers in the complex number form! Absolute value of voltage source (RMS value): V Total impedance of circuit (absolute value): Capacitance: μF Absolute value of current (RMS value) supplied by voltage source: Phase angle of current: degrees Peak value of resistances voltage: 22 A
Consider the circuit in figure given below: A B The capacitor C is initially charged. At time 0, the switch is connected from A to B and the voltage across the capacitor is measured. The following data are recorded by a data acquisition system: t(s) 0.0 0.1 0.2 0.3 0.4 0.5 V(V) 4.98 1.84 0.68 0.25 0.09 0.03 (a) Determine the linear correlation coefficient betweent and V. (b) Determine the linear correlation coefficient between t and In(V).
Capacitance= 9uF Determine the time constant of the circuit for the capacities. For the capacity value, calculate the estimated time to come to the final state. Plot capacitor current and voltage graphs and show if it works in harmony with the time constant you calculated. NOTE: if you want you can use falstad online circuit simulator.
.A series RLC circuit contains a 4-kN resistor, an inductor with an inductive reactance (X,) of 3.5 kn, and a capacitor with a capacitive reactance (Xc) of 2.4 kN. A 120-Vac, 60-Hz power source is connected to the circuit. How much voltage is dropped across the inductor?
A series circuit consists of a resistor, a coil, and a capacitorconnected across a 300V, 60Hz AC source. The current drawn is 20A.The voltage across the resistor is 60V, that across the coil is 260V andthat across the capacitor is 100V. The resultant voltage across the coiland the capacitor is 254.56V. Determine (a) the resistance of theresistor, (b) the resistance and inductance of the coil, and (c) theresistance and capacitance of the capacitor.