The Voltage across PS- and PS+ equals 17.0 volts.The T/C temperature = 103 degrees Fahrenheit.Determine the wire resistance in ohms.Wire Resistance4 to 20 mA current loop250 ohmsMYour Answer:Power Supply24 VDCitType "K" T/CRange 0 to 300 °FTX91APS-PS+MSIN ²IN +* Device is calibrated.

Answered: Image /qna-images/answer/3f2c1294-23f9-4b2b-9178-12b1e81941d3.jpg

The Voltage across PS- and PS+ equals 17.0 volts. The T/C temperature = 103 degrees Fahrenheit. Determine the wire resistance in ohms. Wire Resistance ww 4 to 20 mA current loop Power Supply 24 VDC 250 ohms + ww F Your Answer: Type "K" T/C Range 0 to 300 °F TX91A PS- PS+ M IN O IN + S *Device is calibrated.

The Voltage across PS- and PS+ equals 17.0 volts. The T/C temperature = 103 degrees Fahrenheit. Determine the wire resistance in ohms. Wire Resistance ww 4 to 20 mA current loop Power Supply 24 VDC 250 ohms + ww F Your Answer: Type "K" T/C Range 0 to 300 °F TX91A PS- PS+ M IN O IN + S *Device is calibrated.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 4R: The heating elements in electric water heaters are generally classified into two categories. These...

See similar textbooks

Similar questions

We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
An AC ammeter is connected in series with the primary winding of T1. What is the expected current reading? An AC ammeter is connected in series with the secondary winding of T1. What is the expected current reading? An AC ammeter is connected in series with R1. What is the expected current reading? NOTE: Idc for HW rectifier = 0.318 * Ipeak = 0.45 * Irms Describe/Explain briefly the purpose/use of the array (series-parallel) connection of the rectifier diodes in the given circuit.
Which of the following is NOT a variable in voltametric methods? A. How the current is applied B. How the potential is applied C. The inclusion of convection D. All the above E. Type of working electrode
For the network shown in Figure B22 , assume E = 17V,Diode Di, D2 as Germanium Ri-2KΩ and R2-3ΚΩ. Calculate, i. Current I1, i. Current ID2 ii. Voltage across resistor R2 R1 D1 + E D2 I2 R2 Figure B22
A practical switch is operating at a switching frequency of 100 kHz and a 0.5 duty cycle. The switch is initially on (the first half cycle). The switch has the following parameters: Von = 0.1 V Volt 80 V Ion - 100 A 10.1 A ton = 0 Loft O Ldelay O a) Draw clear voltage and current waveforms for one switching cycle with all values shown (times, voltages, currents, etc.). b) Find the average power loss in one switching cycle.
A certain batch of copper wire was found to have a conductivity of 98% at 20°C. What is its resistivity in u0-cm?
Figure (El1) 12- For the electric circuit shown in the figure (E12), determine the value unar of (R) if the current trough the branch AB is zero and the total current is 1A. Note that all the values of resistors are in ohm. 1.5 B. R 10V Figure (E12) d by
For the network shown in Figure B22, assume E = 18V, Diode D1 as silicon and D2 Germanium, R1=2KQ and R2=3KN. Calculate, i. Current I1, Current In2 iii. Voltage across resistor R2 i. R1 D1 E D2 12 R2 Figure B22
10) A certain batch of copper wire was found to have a conductivity of 98% at 20°C. What is its resistivity in un-cm? www
b) A certain winding made up of copper has a resistance of 100 Q at room temperature. If resistance temperature coefficient of copper at 0 C° is 0.00428/C°, calculate the winding resistance if temperature is increased to 45 C°. Assume room temperature as 25 C°.
For the Cicuit shown in Figure Vec=gV , Bc=1:8Kn ,=100 Zo=7 Ai = ? 39tr 22K 5n %3 C3 Res? Zis? Vi eH
Could you slove this dc electrical circuit