The velocity of water changes uniformly along the transition from VA = 10 m/s to VB = 4 m/s. Pw = 1000 kg/m³ . Assume the fluid is an ideal fluid, that is, incompressible and frictionless. (Figure 1) Part A Determine the pressure difference between A and x = 1.5 m. Express your answer using three significant figures. ? p(x) – PA = – 39875 Ра Submit Previous Answers Request Answer

The velocity of water changes uniformly along the transition from VA = 10 m/s to VB = 4 m/s. Pw = 1000 kg/m³ . Assume the fluid is an ideal fluid, that is, incompressible and frictionless. (Figure 1) Part A Determine the pressure difference between A and x = 1.5 m. Express your answer using three significant figures. ? p(x) – PA = – 39875 Ра Submit Previous Answers Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the fluids (S,, S,) are given in the figure. To vacuum pump P. S, = 0.88 Fluid I 1 1.5 m P 1 1.0 m 0.5 m Pm S, = 0.95 Fluid II Fluid III : Water Unit weight of water, Y. =9.81KN/m³ Atmospheric pressure, Pam = 95.43kPa The gauge pressure value (in kN/m²) up to two decimal places of p, is
In figure 3 compute the pressure head difference between m and n, in feet of fluid A, when: A. Fluid A is gasoline (sp gr 0.715), the gage liquid is mercury, and z = 47.77 in B. Fluid A is oil (sp gr 0.908), the gage liquid is water, and z = 27.77 in C. Fluid A is sea water (w = 64.0), the gage liquid has a specific gravity of 2.95, and z = 57.77
The tank is filled with water and kerosene to the depths shown in (Figure 1). The tank has a width of 3.0 m Take p = 1000 kg/m³, p = 814 kg/m³. Figure A 60° 3 m B 1 of 1 1 m Part A Determine the total resultant force the liquids exert on side AB of the tank. Express your answer to three significant figures and include the appropriate units. FR = μA xa Xb Value a b Provide Feedback Units X. 10m Submit Previous Answers Request Answer X X Incorrect; Try Again; 5 attempts remaining ? www Next >
1.) A pressure in a given tank reads 398 mm of Hg. Determine the equivalent height of a certain fluid in m with sp.gr= 4.33.
Water 0.8 m Immiscible liquid of sp.gr.1.6 1 m What is the gauge pressure at point P in the figure? Assume g = 10 m/s/s.
. Calculate the pressure within the droplet of 11. ưthe velocity distribution of a fluid over a plate is given by u= (3/4) y-y, where uis the velocity in metre per second at a distance of y metres above the plate, determine the shear stress at y = 0.15 metre, Take dynamic viscosity of the fluid as 8.5 x 10 kg-sechn. 12. An oil of viscosity 5 poise is used for lubrication between a shaft and sleeve. The diameter of shaft is 05 m and it rotates at 200 r.p.m. Calculate the power lost in the oil for a sleeve length of 100 mm. The thickness of the oil film is 1.0 mm. [Ans. 3.825 x 10 kgfhu] [Ans. 2.15 kW) 13. The velocity distribution over a plate is given by u=y-y in which u is the velocity in m/sec at a distance of y m above the plate. Determine the shear stress at y = 0, 0.1 and 0.2 m. Take pu = 6 poise. [Ans. 0.4, 0.028 and 0.159 Nm) 14. In question 13, find the distance in metres above the plate, at which the shear stress is zero. [Ans. 0.333 m) 15. The velocity profile of a viscous…
10. The cylindrical container in the figure below weighs 400 N when empty. It is filled with water and supported on the piston. (a) What force is exerted on the upper end of the cylinder? (b) If an additional 600-N weight is placed on the cylinder, how much will the water force against the top of the cylinder be increased? Answer: (a) 51.08 kN; (b) 58.9 kN 250-mm diam A 250 mm B 500 mm?
= What is the gauge pressure at point P in the figure? Assume g 플 Water Immiscible liquid of sp. gr. 1.6 P 0.8 m 1 m 10 m/s²
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
1.- In the following figure the liquid of A and B is water and the liquid of the manometer is oil with a relative density of 0.800 h₁= 25 cms; h₂= 15 cm; ha= 50cms Determine PA-PB in centimeters of water el h2 h3 .800; A B.
6. From the figure shown. Find the pressure head at A when fluid A is seawater (1.03), Fluid B is (s = 2.87); z = 12 in; y = 8 ft Fluid A Fluid B y Sea water
7. The diameters of a small piston and a large piston of a hydraulic jack are force of 60 N is applied on the small piston. Find the load lifted by the large piston, when : (a) the pistons at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jack is given as 1000 . respectively. A kg [Ans. (a) 1500 N, (b) 1520.5 NJ 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/em (gauge), 12.066 N/cm2 (abs.)] m' atmospheric pressure as 10.1043 Nicm. 9. A simple manometer is used to measure the pressure of oil (sp. gr, 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left limb is connected to the pipe. The centre of the pipe is 9 cm below the level of mercury (sp. gr. 13.6) in the right limb. If the difference of mercury level in the two limbs is 15 [Ans. 12.058 N/em²| cm, determine the absolute pressure of the oil in the pipe in N/cm. 10. A simple…