The uniform lamina of density 8 kg/m?. for a=8 m.b=1.5 m,c=1.7 m.d=1.9 m, x-co-ordinate of shape (1) isd2Select one:О а. 0.47ОБ. 0.38Oc 1.90O d. 0.63Oe. 0.95y-co-ordinate of centroid of shape (2) isSelect one:O a. 8.50ОБ. 3.17O. 8.75Od. 10.12Oe. 11.81The total area isSelect one:Oa 12.56ОБ. 16.43Oc. 35.75Od. 19.32Oe. 26.09The x-co-ordinate of total area centroid isSelect one:O a. 1.52ОБ.226Oc 1.05O d. 1.21Oe. 1.42

Given data: a=8 m b=1.5 m c=1.7 m d=1.9 m

The uniform lamina of density 8 kg/m²". for a=8 mb=1.5 m.ca1.7 mde1.9 m, x-co-ordinace of shape (1) is Select one: Oa.0.47 Ob. 0.38 O. 1.90 Od. 0.63 O. 0.95 y-co-ordinate of centroid of shape (2) is Select one: Oa 8.50 Ob. 3.17 Oc 8.75 O d. 10.12 O. 11.81 The total area is Select one: Oa 12.56 Ob. 16.43 O. 35.75 Od. 19.32 O. 26.09

The uniform lamina of density 8 kg/m²". for a=8 mb=1.5 m.ca1.7 mde1.9 m, x-co-ordinace of shape (1) is Select one: Oa.0.47 Ob. 0.38 O. 1.90 Od. 0.63 O. 0.95 y-co-ordinate of centroid of shape (2) is Select one: Oa 8.50 Ob. 3.17 Oc 8.75 O d. 10.12 O. 11.81 The total area is Select one: Oa 12.56 Ob. 16.43 O. 35.75 Od. 19.32 O. 26.09

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.26P: Using the method of composite areas, find the dimension h that maximizes the centroid coordinate y...

See similar textbooks

Similar questions

Compute the surface area of the axi-symmetric domed structure.
By integration, find the centroid of the surface of the hemisphere. Compare your result With Table 8.4.
Using the method of composite areas, find the dimension h that maximizes the centroid coordinate y of the plane region shown.
The equation of the catenary shown is y = 100 cosh (x/100) where x and y are measured in feet (the catenary is the shape of a cable suspended between two points). Locate the y-coordinate 0f the centroid of the catenary by numerical integration using x=25ft.
Use numerical integration to locate the centroid of the symmetric plane
Small screws are used to fasten a piece of hardwood to the bracket that is formed from 1/20-in.-thick steel sheet metal. For steel, =0.283lb/in.3, and for hardwood, =0.029lb/in.3. Locate the center of gravity of the assembly.
1. Locate the centroid of the following figures. 90 mm : y a) b) 90 ty 4 in mm 3 in 120 X + 2 in 2 in 2 in A = A1 - A2 Ax = A1 x1 - A2 x2 А у%3DA1 y1 - A2 у2 A = A1 - A2 Ax = A1 x1 - A2 x2 А у 3DA1 y1 - А2 у2 2. Compute for the moment of inertia about xo and yo of the following figures. а) b) y 100 mm 100 mm 75 mm y 25 mm 120 mm 75 mm 50 mm 180 mm | = |1 - 12 |= 1 + 12
19% @ uo 10:27 quiz1.docx Locate the centroid z of the right-elliptical cone. 10 ft 4 ff
Q. 2 Find the kocation of centroid of shaded area with respect to reference axes x and y r=16 cm 8 cm 8 сm
Locate the centroid of the plane area shown. Given, A= 15 cm, B= 9 cm, C= 3 cm. (0,0) - Select the closest choice to your solution and ONLY TYPE THE LETTER IN THE BLANK (A, B, C, D). The centroid in the x direction with respect to the given x axis: A. 9.8 cm B. 5.16 cm С. 13.03 ст D. 8.17 cm (Q1)
50 mm 150 mm 150 mm 300 mm find the moment of inertia for this exercise, with the following formulas: Polar Jo= Iox + + Toy Iox - Icx + Adg² Toy = Icg + dobe ² Caculation of centroid attached below. use it to solve the question in red box asap Som Av 3com for Portion A₁ - the figure is symme about y-aris. 2=0. AL 120mm AALD Area of A₁ = 300x50 = 15000 Y₁ = y₁ y = 300 for Pation A2 Area Az = 50x300 = 15000 By Considering Centroid, from the Bottom of the section. 300+ 50 = ₁ + 3/2 = 325 Centroid (ā, y) = = [0₁ SE = 50mm A, Ya+ A₂4 0, A₁+A₂ 15000x150 +15000x325 15000 15000 (0.237.5)
10 - Find the center of gravity M (x,y,z) of the three-dimensional homogeneous ABCD wire in the figure by using the coordinate set. The dimensions of the wire are a= 24 cm, b= 36 cm. In which of the following options are the coordinates of the CD part of the homogeneous wire in the x, y and z axes correctly given?A) (18 ; 24 ; 0)B) (18 ; 12 ; 24)C) (18 ; 12 ; 0)D) (18 ; 24 ; 24)E) (18 ; 24 ; 12)