Problem 6Two cables of the same gauge are attached to a transmission tower at B.Because the tower is slender, the horizontal component of the resultant of theforces exerted by the cables at B is to be zero. Knowing that the mass per unitlength of the cables is 0.4 kg/m, determine (a) the required sag h, (b) themaximum tension in each cable.-90 m-AhB60 m→3 mFigure Problem 6с

Answered: Image /qna-images/answer/d8cac1ea-f615-4592-b360-138bce4a07e7.jpg

the Two cables of the same gauge are attached to a transmission tower at B. Because the tower is slender, the horizontal component of the resultant of forces exerted by the cables at B is to be zero. Knowing that the mass per unit length of the cables is 0.4 kg/m, determine (a) the required sag h, (b) the maximum tension in each cable.

the Two cables of the same gauge are attached to a transmission tower at B. Because the tower is slender, the horizontal component of the resultant of forces exerted by the cables at B is to be zero. Knowing that the mass per unit length of the cables is 0.4 kg/m, determine (a) the required sag h, (b) the maximum tension in each cable.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

system at point A. Then determine the distance: Reduce the given loading system to a force-couple to the right of point A at which the resultant of the Reduce the given loading system to a to the right of point A at which the resultant of the three forces acts. 720 N 800 N 200 mm 500 mm 450 mm 1200 N
STATICS OF RIGID BODIES Determine a. The component of the force F acting along the cable AC b. The angle the force F makes with cable AC.
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Determine the average normal strain in each wire. The wires are unstretched when the lever is in the horizontal position. 200 mm 200 mm 300 mm -300 mm- E B D 200 mm H
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
The rigid beam is supported by three rods, each having a cross- sectional area of 850 mm?. Rods AB and CD are made of A E 2014-T6 aluminum, while rod EF is made of 304 stainless steel. 150 kN 80 kN All three rods were exactly 3.0 m long when they were installed 3 m al al st at a temperature of T = 10°C, before the loads were applied. B F (a) Determine the force in each rod after the loads are applied, assuming the temperature is still 10°C. - 2 m-- 2 m---2 m--2 m-| (b) If the temperature subsequently rises to T2 = 40°C while the loads are applied, determine the new force in each rod. Neglect the weight of the beam.
Three pulleys are joined by solid steel shafts AB and BC. If G = 200 GPa, determine the unit shearing stress in shafts BC. In MPa A 25 mm ara B 450 N-m 1.2 m 1300N-m 38 mm dia 1.80 m 900 N-m
Problem I A 2.25-kg slender rod AB and a 1.85-kg slender rod BC are connected by a pin at B and by the cord AC. The assembly designed by engineers can rotate in a vertical plane under the combined effect of gravity and a couple M applied to rod BC. Knowing that in the position shown, the 300 mm angular velocity of the assembly is zero and the tension in cord AC is equal to 25.0 N, determine; A (a) the angular acceleration of the assembly (b) the magnitude of the couple, M 400 mm C 400 mm AM B
M E You have 2 Thank You Best Regare Ms. Nur Akr Figure Q3 shows a truss structure, which is pinned at A and roller supported at B. Horizontal load are applied to the truss as shown in the Figure. By using section method, solve the force in member AC, CD and DE in the figure shown (CO2, PO2, C3). 20KN 10KN 3.5m H →10kN 3.5m E 3.5m D H 15kN 10kN- 5kN G C A 5.0m 3.5m B 000 5kN 5kN Gmail M
Q4) Determine the maximum shear stress acting in the fiberglass beam at the section where the internal shears force is maximum. (tı=15 mm, t2=20 mm, h=150 mm, b=50 mm) 。王! 20 kN/m A |-b-| to 2 m 2 m - 2 m
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
4. Determine the x, y, z components of reaction at the ball-and-socket joint A and the tension in each of the wires, if the load weighs 100kg. 1m 2m 1m D F A 1.5m B G 1m, 1m 1m.
View Policies Current Attempt in Progress A load of P = 150 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 100 GPa] rods (1), and a solid steel [E = 200 GPa] rod (2), as shown in the figure. All rods are unstressed before load P is applied to the rigid bar directly underneath joint B. Assume perfect connections at all joints. The bronze rods (1) each have a length of L1 = 2250 mm, a diameter of 28 mm, and a cross-sectional area of 616 mm?. Steel rod (2) has a length of L2 = 1750 mm, a diameter of 20 mm, and a cross-sectional area of 314 mm?. Determine the axial force that is produced in steel rod (2) after load P is applied to the rigid bar. a a (1) (1) L1 L2 (2) OB Answer: P2- i kN