The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a roller at A and a pin at E. The force in member (AB) is equal to. 1000 Ib 1000 lb 1000 lb 130° BI D -10 ft -10 ft -10 ft- -10 ft 1000 lb Select one: a. 2598.07 lb - compression b. 2598.07 Ib – Tension c. 3000 lb – Tension d. 1732.1 Ib - Tension

The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a roller at A and a pin at E. The force in member (AB) is equal to. 1000 Ib 1000 lb 1000 lb 130° BI D -10 ft -10 ft -10 ft- -10 ft 1000 lb Select one: a. 2598.07 lb - compression b. 2598.07 Ib – Tension c. 3000 lb – Tension d. 1732.1 Ib - Tension

Name: 2:50 O PO N 38%三Question 3Not yet answeredMarked out of 15.00P Flag q
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 2:50 O PO N 38%三Question 3Not yet answeredMarked out of 15.00P Flag questionThe truss is subjected to the system offorces as shown in the following figure. Thetruss is supported by a roller at A and a pinat E. The force in member (AB) is equal to.10

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Similar questions

Q5/A) From the figure below, determine the reaction force at pin C. A 000 0.6 m 10 kN 0.6 m 0.8 m 60° 0.4 m 6 kN OB
TDE= TBE Required information The structure consists of pin-connected members. Take X = 4 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. = 2m Determine the force supported by all members. Enter forces as positive numbers if the member is in tension and as negative numbers if the member is in compression. (Round the final answers to four decimal places.) The force supported by all members are as follows: TAB -7.0711 KN TAD= -5 KN TBD= 2.2361 kN KN |1m-1m-1m-1m4 2 kN 3 KN X 3 KN D TEF= TBF= 4.4721 TCF= TBC= -5.6569 kN KN E KN KN F C
oft Word - Test 2 Practice x T Tech|Express B Homepage - Tennessee Technolo x pads/Test%202%20Practice%20Problems.pdf ms 5 / 6 100% If the roller at B can withstand a max load of 3 kN, determine the largest magnitude, F, of the three applied forces. Ans. F = 354 N Problem 9: 2 m 45° 2 m 2 m 2 m F F N 50°F Clear ヘ x の f11 f9 144 h2ナ insert 14 15 %, & 4 7. 8. 6. 1
The lifting arm shown below needs to lift a weight of 4 (N). Assuming the links are weightless, determine the magnitude of the force being applied by the pin at B on the lifting arm to the nearest hundredth of a newton. 10Em) 6icm- 150 A Servo Horn Arm 4 (W) 'Servo
1. A tripod shawn supports of note that ball and rocket joints are used to mount the tripuod a load P=1000N at point A. Take at points B,D, and C. consider the t LI L 2 L2: 4 L3 : 3 A : 45° g :30° %3D on x-z plane L2 POINT C (2,-2,3) C0,0,0) ミー- Determine the ff Force of AB - N Force of AC - N Force of AD : N
Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last digits number pf your IC) 4m 400 KN 10 m B 60 KN 4m 10 m. 157KN 4m 17 m D
Q2): Body A is weight 100 N and tied to a rigid wall using a steel cable and it is located on body B of weight 300 N which rest on a rough surface (coefficient of fraction is 0,3). If the fraction coefficient between body A and B is equal to 0.25 and the pulling force P= 600 N. calculate the tension force of the steel cable. A 530 37 B TTTTTT
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. kys Part 1 B 3.1 m AD 50° CD Answers: AD = The Free-Body diagram for joint D is drawn assuming that all internal forces are in tension. Solve for the forces in AD and CD. The forces are positive if in tension, negative if in compression. 50 CD = i 6.2 m 50 D 50° 3600 N 3600 N N N
Required information Stairs leading to a balcony are shown below. |400 lb dimensions in inches 40° 144 600 lb 32 22 16 38 30 30 For the 400 lb and 600 lb forces, and if F= 155 lb and P= 0, determine the reaction at point Dand the force supported by bar BE. The reaction at point Dand the force supported by bar BE are as follows: Dy= 410 Ib TBE = - 701.798 Ib
N and Determine the force in cables N necessary to support the 12 kg traffic light shown in figure. (Hint: Please just enter the numerical value without any unit and use three significant digit only. For example if AB= XXX N then enter only XXX.) Answer. = 24 1.63// KSI. 12⁰ B
An L-shaped bar is supported by a bearing at A and a smooth horizontal surface at B. Take the value of Fto be 720 N. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 1.5m 1.5m 2m Determine the reactions at A and B. (Do not include a minus sign in your response.) The y component of the reaction force at A is [ NT. The z component of the reaction force at A is N✓. The reaction moment at A about the y axis is N-m . The reaction moment at A about the z axis is N.m O The y component of the reaction force at Bis NT.
Calculate Tension BD if P = 100 kN. 1m 2.5 m 250 N -1.5 m- 2 m 1.5 m- Use the editor to format your answer