The transistor in the circuit below has 3 = 100 and VBE = 0.7 V in forward bias. Ignore the Early effect and use VT = 25 mV. 6 V O + 6 V 10 k Vsig o Vout a) Is this amplifier a common-emitter, common-base, or common-collector configuration? Determine the collector current and show that the transistor is biased in the active mode. b) Calculate the amplifier's small-signal gain A, the input resistance Rin, and the output resistance Rout- Don't include the 10 k resistance of the signal source or the 1 k load resistor. But do include the effect of the 180 k biasing resistor. c) Calculate the system gain; G = vout/Vsig- 180 k 1k

The transistor in the circuit below has 3 = 100 and VBE = 0.7 V in forward bias. Ignore the Early effect and use VT = 25 mV. 6 V O + 6 V 10 k Vsig o Vout a) Is this amplifier a common-emitter, common-base, or common-collector configuration? Determine the collector current and show that the transistor is biased in the active mode. b) Calculate the amplifier's small-signal gain A, the input resistance Rin, and the output resistance Rout- Don't include the 10 k resistance of the signal source or the 1 k load resistor. But do include the effect of the 180 k biasing resistor. c) Calculate the system gain; G = vout/Vsig- 180 k 1k

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Activity 2: The amplifier circuit below has a single ac input and two ac outputs. Assuming transistor parameters of B= 130 and VBE=0.7 V: 15 V 15 V W 350 ΚΩ 300 ΚΩ H11 13 ΚΩ 10 ΚΩ
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. Calculate the current gain, the input resistance, and the output resistance.
Correct the sentence: The aim of using coupling in multistage transistor amplifiers is to transfer DC output of one stage to the input of the next .stage and to isolate the d.c. conditions of one stage from the next stage
1. N-channel enhancement MOSFET control voltage is applied at the controlling the current that is the drain terminal Select one: a. source, entering b. gate, entering C. drain, entering d. source, leaving e. gate, leaving f. drain, leaving 2. In a common source amplifier, the input is fed to the while the output is taken from the Select one: a. source, gate b. source, drain C. gate, source d. gate, drain e. drain, source f. drain, gate 3. In the saturation region of a MOSFET, choose all of the equations that apply (Hint: there are 3) Select one or more: a. VGS >= VTH b. VGS = VGS- VTH g. VDSVGS- VTH ID-k[(2(VGS-VTH)VDS-VDS²]
2 a) i) Draw typical output characteristics of a common emitter npn transistor and clearly identify the active, saturation, and cut off regions on your drawing. ii) Explain how you can find the common emitter de current gain, B, and the common emitter ac current gain, hre, from the common emitter output characteristics of an npn transistor. You need to draw typical output characteristics in scales and provide numerical calculations to support your explanation.
2. The circuit in Figure 2 has a BJT transistor with B= 200, VA = 20 V. Determine BJT DC collector current and DC collector voltage. Determine the small-signal input resistance seen by the AC voltage source, the output resistance at Vout, and the transfer function Vout/Vin. HH 1.7 V 100k Figure 2, Problem 2 10 V 2k Vout 2k
Given a D-MOSFET circuit used as an amplifier with the following parameter: IDSS=12mA and a transconductance of gm=3.2 mS. Determine the DC drain to source voltage VDS and the AC output voltage if Vin=500 mV.
ASAP
The amplifier in the circuit below is driven by a signal generator v, with a small sine wave signal vhose average value is zero. Assume the transistor has a value of B-100, and V-26 mV. a. You need to design the circuit so that the de emitter current IE of the emitter resistor RE to establish the desired de emitter current. = 1 mA. Specify the value b. A de collector voltage of +5 volts is desired. Specify the value of the collector resistor Re to establish the desired de collector voltage. For this part assume that RL 5 K and the Early Effect needs to be considered. The transistor has a VA 100 Volts. Draw the ac small signal equivalent circuit model of the amplifier and determine its voltage gain. 91SV C. 2.5k MM do RE -15 V 84 Vout RL
1 The AC input to a common emitter amplifier (Figure 1) is such that it is comparable to thermal voltage VT. For such an amplifier: a. Please show how a hybrid – T small-signal model would look like. Do not ignore early effect. b. Please derive relation for the terminal voltage gain and overall voltage gain. Vcc Rc R RE C Figure 1 You uolont oirouit
Consider the circuit in Figure 2. The transistor has a parameter B that varies between 50 and 200. You want to know the operation of the circuit and the electrical variables at the end points. Calculate the following for B= 50 and B= 200. a) IE, VE and VB (Analysis in DC). b) The input resistance R." (Small signal analysis). c) The voltage gain VO/Vsing (Small signal analy). This 10 ΚΩ www o Rin 100 ΚΩ +3V +1₁ HH 1 ΚΩ 1₁ 1 ΚΩ
. Part a: List the elements included in the total input resistance of a common-collector amplifier. What is the phase relationship of the input and output voltages of a CE(common emitter) and CC(common collector) amplifier?