The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20 bolts with diameter of 20 mm. The vessel has an outer diameter of 1 m. If the vessel has an internal gauge pressure of 1.77 MPa and experiences an external force 10.5 kN, determine the circumferential stress and the longitudinal stress in the vessel wall, the normal stress in the bolts, and the bearing stress on the plates due to the nuts on the bolts if the contact area on the nuts have an outer diameter of 37 mm and inner diameter of 20 mm.

The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20 bolts with diameter of 20 mm. The vessel has an outer diameter of 1 m. If the vessel has an internal gauge pressure of 1.77 MPa and experiences an external force 10.5 kN, determine the circumferential stress and the longitudinal stress in the vessel wall, the normal stress in the bolts, and the bearing stress on the plates due to the nuts on the bolts if the contact area on the nuts have an outer diameter of 37 mm and inner diameter of 20 mm.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A typlcal aluminum-alloy scuba diving tank is shown. The outside diameter of the tank is 200 mm and the wall thickness is 12 mm. If the air In the tank is pressurized to 16MP3, determine the maximum shear stress in the plane of the cylinder wall. O 29.3 MPa O 33.7 MPa O 27.4 MPa O 40.7 MPa O 21.0 MPa
Question 4. Three wires are used to suspend the plate shown. Aluminium wires are used at A and B with a diameter of 3 mm and a steel wire is used at C with a diameter of 2 mm. Knowing that the allowable stress for aluminium (E = 72 GPa) is 96 MPa and that the allowable stress for steel (E = 200 GPa) is 124 MPa, determine the maximum load P that may be applied. L L P B
A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shown below. Do not consider the stress concentration! a) Determine the principal stresses at Scction B-B?. b) Determine the principal stresses at point A? 3 kN Y R30 L, A 125 09
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
For the pin connection shown, determine the normal stress acting on the gross area, the normal stress acting on the net area, the shear stress in the pin, and the bearing stress in the steel plate at the pin. Please explain the solution
The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. The tank is designed to withstand a pressure of 2.1 MPa. The tank and the 25-mm-diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. Part A Determine the required minimum thickness of the cylindrical shell. Express your answer to three significant figures and include the appropriate units. ANSWER: tc = Part B Determine the required minimum thickness of the hemispherical shell. Q Tap image to zoom Express your answer to three significant figures and include the appropriate units. ANSWER: th =
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Mpa. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm mm. 50 mm 340 mm
3. A spherical pressure vessel has a D (mm) inner radius and thickness of 45mm. It is constructed by joining two hollow hemispheres connected by 10nos of 28mm dia bolts along the circumference. Working tensile stress of the vessel is 40 MPa while the tensile stress of the bolt is (o) MPa. (a) What is the maximum allowable internal pressure considering only the capacity of the bolts? (b) What is the maximum allowable internal pressure considering only the capacity of the vessel? (c) What is the maximum allowable internal pressure of the structure in Megapascals Assume: D = 761 σ = 461
Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138, Detennine the maximum tensile load that can be applied if the stress is limited to 115 MN/m2. B. What force is required to punch a square hole (25-mn*25mm) in a plate that is 30 mm thick? The shear strength is 350 MN/m2. Puncher 25 mm 25 mm 30 mm hick
The gas storage tank is fabricated by bolting together two half cylindrical shells and two hemispherical shells as shown in Figure 4. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4m. If the tank is designed to withstand a pressure of 3 MPa, a. Determine the required minimum thickness of the cylindrical and hemispherical shells b. Determine the minimum required number of bolts for each hemispherical caps. Figure 4
Situation 1: A rigid bar ABC weighs 10 kN/m. The compressive stress of the copper bar is 20 MPa. Answer the following questions: 3m B 2 m Copper L=3m A = 1500 mm² Brass C L = 2 m A = 1200 mm² A. What is the stress of the brass bar? Indicate if it will experience tension (T) or compression (C) (MPa) B. What is the minimum required diameter of the pin at A assuming that the pin connection is in double shear? Consider the allowable shearing stress of the pin as 15 MPa. Round your answer in a multiple of 5. (mm)
The structure shown below is hinged to fixed supports at A and C. The bars are each 4 in. by 4 in. in section. Compute the maximum tensile stress developed in bar CB assuming the pin connections at A, B, and C are frictionless. Group of answer choices 2300 psi 2800 psi 1150 psi 4600 psi