The T-section in the figure was created by gluing two rectangular wooden planks of 18 cm in size with glue. Since the glue value of the shear force affecting the section is Ty = 10kN, determine what the minimum safety stress of the glue should be in order to ensure joint security. (Ix = 11016 cm ^ 4) Write the result after the comma, rounding it to two decimal places and specifying. 18cm T. T. 6cm tutkal 18cm Y15cm 6cm

The T-section in the figure was created by gluing two rectangular wooden planks of 18 cm in size with glue. Since the glue value of the shear force affecting the section is Ty = 10kN, determine what the minimum safety stress of the glue should be in order to ensure joint security. (Ix = 11016 cm ^ 4) Write the result after the comma, rounding it to two decimal places and specifying. 18cm T. T. 6cm tutkal 18cm Y15cm 6cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Joints B and D use a pin with a diameter of ø10 mm. In connection C, the diameter of the pin is ø6 mm. The permissible shear stress τmax of the pins is 75 MPa and the permissible normal stress σmax of the rod BD is 200 MPa. Determine the maximum allowable value of the force P. Units [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer! Dimension L = 300 mm
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 80.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 4.70 MN, pressure vessel bolts aide port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.
asap
The length AB of the horizontal beam is L = 2400 mm and the height b = 51 mm. Determine the maximum force F that the horizontal bar will withstand without buckling. The Euler formula is used to examine the buckling. The modulus of elasticity of the material E = 210 GPa Use units [N, mm] Please enter an answer to one decimal place. Do not round off the invoices in the intermediate stages, but only the final answer! (right pictue: support A from the top)
Question 1. W₂ y: ← WI Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown above (not drawn to scale). The bottom section has width w₁ = 10mm and height h₁ = 60mm. The top section has width w₂ = 50mm and height h₂ = 14mm. Enter your answer in millimetres correct to two decimal places. mm hi Type here to search 122 4313 O Af
Please answer all becuase they are all connected! UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic material having a tensile and compressive yield stress of o,, determine the following: Given: Allowable Stress = 300 MPa a = 20 mm b = 250 mm c = 250 mm This is already answered in bartleby but please recheck. Thanks a. Calculate the moment of inertia I, in x10 mm4 (If your answer is 667,335 x10 mm, then type 667.335) b. Calculate the yield moment of the section in kN.m. c. Calculate the plastic moment of the section in kN.m d.Calculate the shape factor of the section.
Write the solution for the following: Member BC = -447.21 Member DF = -800 Member CE = 100
Build the following part and report the volume in units cubed. A = 48 B = 51 R20 R10 B 30 50 2X R10 R20 Ø20 A 10 TYP DESIGN ERICS DRAWING TITLE
Determine the spacing of vertical stirrups near the left support of the "L"(m) beam loaded as shown below. The concentrated load is placed x meters from A. Use "n" legged stirrups with given diameter below. Round down your answer to the nearest whole number. USE SIMPLIFIED CALCULATION and NSCP 2015 mm 320 mm 520 mm wu fc' 35 MPa fyt 415 MPa L-x Pdl 60 KN PII 70 KN 25 KN/m wll 35 KN/m ф bar 12 mm 3 0.4 m length
The lace Facts on the bracket within the octant shown in Fig.1) Figure Part A HF-520 N-65 and y 45", determine the zy z components of F Enter the components of the force separated by commas. Express your answers in newtons to three significant figures Az ivec 0 F. P. F. Submit Provide Feedback Request Answer ? N
The square deforms into the position shown by the dashed lines. (Figure 1) The dimensions are S = 55 mm, S' = 60 mm, Az1 = 5 mm, and A₂ = 8 mm. Side D'B' remains horizontal. Figure 91.5 ATL Ax₂ 1 of 1
The axial load 229kN applied to the lap joint is distributed equally among the three 17.1-mm-diameter rivets. What is the maximum tensile stress (in Mpa) in the plate if w=139.6mm and t=29mm? Round off the final answer to three decimal places.