The stress induced in a body, when subjected to two equal and opposite forces which are acting tangentially across the resisting section resulting the shearing of the body across its section is called a) Bending stress b) Compressive stress c) Shear strain d) Shear stress

The stress induced in a body, when subjected to two equal and opposite forces which are acting tangentially across the resisting section resulting the shearing of the body across its section is called a) Bending stress b) Compressive stress c) Shear strain d) Shear stress

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 44 Transforming the coordinates of the shear stress from cartesian to spherical coordinate system allows to better visualize the dynamics of the tensor on a spherical geometry. A) True B) False
c) Reduce a System of Forces to a Single Resultant Force? R MA R B
Direct stresses of 160N/mm2 tensile and 120 N/mm2 compressive exist on two perpendicular planes at a certain point in a body. They are also accompanied by shear stresses on the planes. The greatest principal stress at the point due to these is 200 N/mm2. a) What must be the magnitude of the shearing stresses on the two planes? b) What will be the maximum shearing stress at the point?
P1. The below picture shows a three-point bending test of the bone specimen, Given the below loading condition a) Draw shear force diagram b) Determine the maximum shear force c) Determine the maximum transverse shear stress in the bone 1000N 25cm c=2cm 5cm 50cm 5cm 500N 500N Note: Use the following centroid formula for half circle when you calculate Q Centroid (X,y) (Answer: Tmax =0.53MPA) 4r 3
The stress-strain curve below is for an epoxy-carbon composite: Stress Strain Curve Composites 3.0010 2.5010 2.0010 1.50E10 1.00+10 5.00E09 0.15 02 Strain The mechanical properties of the component materials are in the table below: E (GPa) Strength (MPa) Elongation () Ероху (Rein) 3 100 6 Carbon Fibre (Fibre) 300 7500 a) Using the data in the graph, estimate the stiffness of the composite. b) Calculate the volume fraction of the fibres. Assume the fibres are in the longitudinal direction. c) What is the theoretical strength of the composite? Stress in Pascals
A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a Poisson's ratio of 0.35 is pulled in tension with a force of 40, 000 N. If the deformation is totally elastic, what is the strain experienced by the specimen along the lateral direction? A) -0.00029 B) -0.01350 c) -0.00041 D) -0.00116
The metal stud punch is subjected to a force of 180 N on the handle A) Determine the magnitude of the resultant internal normal force acting on the cross section of the handle at point E. B)Determine the magnitude of the resultant internal shear force acting on the cross section of the handle at point E. C) Determine the magnitude of the resultant internal bending moment acting on the cross section of the handle at point E.
3. Replace the loads acting on the beam, as shown by a single resultant force R and find its location on the beam. 8 kN 6kNm 4km Pl 6 4m 1m 1m A) R = 40 kN ↓, 4.03 m to the right of 4. B) R=40 KN, 3.55 m to the right of 4. C) R = 40 kN ↓, 4.26 m to the right of A. D) R = 50 kN ↓, 3.55 m to the right of A. ВО 000
QI) A rod 150 cm long and diameter 2 cm is subjected to an axial pull of 20 kN. If the modulus of clasticity of the material of the rod is 2 10 N/mm'; determine: a) The stress b) The strain, and c) The clongation of the rod.
a) 1. The support reaction forces at the A and C, in terms of P,be careful of the sign. 2. Give the expressions of the shear and moment at an arbitrary poistion x of AB segment, in terms of P and x, be careful of the sign. 3. Give the expressions of the shear and moment at an arbitrary poistion x of BC segment, in terms of P and x, be careful of the sign. b)Given l= 1000 mm, P= 4000 N and l1/l=0.66, calculate the internal shear force and draw the moment diagram
F=180 N A) Determine the magnitude of the resultant internal normal force acting on the cross section of the short link BC. B) Determine the magnitude of the resultant internal shear force acting on the cross section of the short link BC. C) Determine the magnitude of the resultant internal bending moment acting on the cross section of the short link BC.
F= 920 lb a)Determine the normal force acting at point D. b)Determine the shear force acting at point D. c) Determine the moment acting at point D.