The stream function for potential flow over a spinning cylinder is given by: u (r₁0) = Voo Sin O Determine the location of the stagnation points when a) k = Voo a b) k = 0 Posesible useful information : sin go = Sin 360° Sın 30° = Sin 150° Sin 45° Sın 135° Sin 90° = 1 = = [r- a² ]-k in a 0 = 0.5 = 0.707

The stream function for potential flow over a spinning cylinder is given by: u (r₁0) = Voo Sin O Determine the location of the stagnation points when a) k = Voo a b) k = 0 Posesible useful information : sin go = Sin 360° Sın 30° = Sin 150° Sin 45° Sın 135° Sin 90° = 1 = = [r- a² ]-k in a 0 = 0.5 = 0.707

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The potential function of fluid flow motion is given by, [(x+c)2+y²7 p = log la-e)2+y². a) Prove that, fluid is incompressible, b) Find the velocity field, c) Find the geometric location of the providing IV? = constant. %3D
Moving to another question will save this res Question 10 The static temperature of a moving fluid is greater than stagnation pressure equals to stagnation temperature greater than stagnation temperature smaller thag stagnation temperature AMoving to another question will save this respon
Please indicate the given, assumption and illustration. A source with strength 0.25 m2/s and a vortex with strength 1 m2/s (counter-clockwise) are located at the origin. After working out the equations for the stream function and velocity potential components, determine the following velocity components at a point P(1, 0.5): A) The Radial Velocity component in meters/second. B) The Tangential Velocity Component in meters/second.
Question 25 U=4m/s Ps Po Ultimate width (link to image) A pitot static probe in a uniform air flow of 4 m/s can be modelled in 2D using a source placed at the origin. The ultimate width of the pitot-static probe is 7 mm. a) The location of the leading edge of the probe is x = v mm, y =0 mm b) The probe's static tapping is placed at x 0.8 mm, y = 2.1mm, the magnitude of the flow velocity at this point is v m/s
4. The velocity vectors of three flow fileds are given as V, = axĩ + bx(1+1)}+ tk , V, = axyi + bx(1+t)j , and V3 = axyi – bzy(1+t)k where coefficients a and b have constant values. Is it correct to say that flow field 1 is one-, flow filed 2 is two-, and flow filed 3 is three-dimensional? Are these flow fields steady or unsteady?
Fluid dynamics: Potential flow
Shallow-water velocity equation a. Confirm that the linear approximation to f(x) = tanh x at a = 0 is L(x) = x. b. Recall that the velocity of a surface wave on the ocean 2nd tanh - In fluid dynamics, shallow is v = water refers to water where the depth-to-wavelength ratio d/A < 0.05. Use your answer to part (a) to explain why the shallow water velocity equation is v = Vgd. c. Use the shallow-water velocity equation to explain why waves tend to slow down as they approach the shore.
Questions 01: Write short note on *Fluid kinematics. *Control volume . *lagrangian Flow description . *Evlerian flow Description.
Dimensional Analysis and Hydraulic Similitude (fluid mechanics) 1. Water at 60F at 12 ft/s in a 6-in. pipe. (a) For dynamic similarity, determine the velocity of medium fuel oil at 90F flowing in a 12-in. pipe. (b) Determine the diameter of the pipe that should be used if a medium lubricating oil at 70oF if flowing at a velocity of 50 ft/s. find the: a. velocity : ____________________ fps b. diameter : ____________________ in.
PLEASE ANSWER THEM ALL FOR AN UPVOTE. THANK YOU. Given: Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Ans. the ff questions. •What is the pressure in MKS unit? •What is the pressure in CGS unit? •What is the viscosity of the liquid? • If the weight was given as 8.5 grams, what will be the density of the liquid? •What is the kinematic viscosity of the liquid? •What is the fluidity of the liquid?
Given a velocity field as V(x, y, z) = axî – ayĵ %3D With units of velocity in m/sec; x and y in meters; and the constant coefficient a = 0.1 sec. a) Determine the equation for the streamline passing through the point (x, y, 0) = (2, 8, 0). b) Determine the velocity of a particle at the point (2, 8, 0). c) If we mark the particle passing through the point (xo, Yo, 0) at to = 0, determine the location of the particle at time t = 20 sec. d) Show that the equation of the particle path (the pathline) matches the equation of the streamline.
The line generated by a tracer fluid, such as a dye, continuously injected into the flow field at the starting point.A. Streamline B. Streakline C. Pathline D. Baseline