The steel frame work is used to support the 4-in. reinforced stone concrete slab that carries a uniform live loading of 370 lb/ft². Set a = 9 ft. b = 12 ft. Assume that the beams AF and CD are not supported by the girder FED, therefore the forces that the beams AF and CD exert on their supports at F and D do not act on FED. Hint: See Tables 1.2 and 1.4 in the textbook. (Figure 1) Figure B 1 of 1

The steel frame work is used to support the 4-in. reinforced stone concrete slab that carries a uniform live loading of 370 lb/ft². Set a = 9 ft. b = 12 ft. Assume that the beams AF and CD are not supported by the girder FED, therefore the forces that the beams AF and CD exert on their supports at F and D do not act on FED. Hint: See Tables 1.2 and 1.4 in the textbook. (Figure 1) Figure B 1 of 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each member of the truss using method of joints. State if the members are in tension or compression. 40 kN G 3 m 20 KNE F 20 KN 2 m 5m A C 40 kN 1-3- 2 m NE SE m Bu m 40 kN NE + ME m m B
3.30 For the truss and loading shown, determine the resultant of the loads and the distance from point A to its line of action. R d 4 kips 3 kips 2 kips E 6 ft B O 00 8 ft 8 ft 8 ft 8 ft
"""The pratt truss shown carries a group of live loads at its bottom chord. determine the maximum stress of members BC, using influence line.""
5.(c) Derive an expression of Euler Bucking load when one end fixed and other hinged.
*4-148. Replace the distributed loading by an equivalent resultant force and specify its location, measured from point A. 200) Nim 2m - 3m
What is the approximate axial force in girder EF of the frame shown? Use the portal method. G H 80 kN 6 m 40 kN D E 6 m B -10 m- -10 m- O a. 20kN O b. 30 kN O c. 10 kN O d. 60 kN
18 12⁰ PLAN SECTION =1 S B1 B2 B3 B F 10 cantilevered beams columns W The load per foot on Joists J-1 is larger than b. The load per foot on Beam B-1 is larger than c. In which column does the largest axial stress occur? N S 2. The roof of a small building schematic plan and section. Closely spaced joists (J-1 and J-2) span north-south and bear on Beams (B-1, B-2 & B-3) which in turn bear on Columns A-F. The Beams cantilever 10' beyond the east row of columns. All joists are spaced the same distance on center All columns have the same cross section area of 30.0 in² Roof Live Load = 40 PSF Roof Dead Load = 30 PSF as shown in the Allowable axial stress in columns, Fa= 1000 psi (Neglect the self-weight of columns) smaller than smaller than the same as the load per foot on Joists J-2 the load per foot on Beam B-3 the same as A B C D E F How large is the axial stress in the column selected in Part (c)? (For this problem, disregard effects of slenderness, and simply calculate the axial…
Problem 1: A roof truss is made with an angle bar 50mmx25mmx6.35mm connected as shown. The material used is cold drawn steel. Neglecting the weight of all the connectors, compute the total dead load caused by the truss. Also, determine the vertical reaction at each support due to the weights of the truss. 4 m B 4m- C m D 4 m E 3 m 3m
Replace the loading acting on the beam by a single resultant force. Specify where the force acts, measured from end B.
How many zero-force member on the structure as shown below. a.) F F F b.) 1 kip 0.5 kip 3 kips 2 kips H 2 kips 1.5 kip D M R
H.W1: Find the stability and determinacy of frame below
For the propped cantilever shown in the figure, a hinge is provided at C. A and B are at the same level. What is the force reaction at the fixed end A? P ff. A с 1/4 1/4 1/2- B