The shear leg derrick is used to haul the 350-kg net of fish onto the dock. Determine the compressive force along each of the legs AB and CB and the tension in the winch cable DB. Assume the force in each leg acts along its axis. D 7.5 m 4.5 m 3 m 3 m B 4.5 m

The shear leg derrick is used to haul the 350-kg net of fish onto the dock. Determine the compressive force along each of the legs AB and CB and the tension in the winch cable DB. Assume the force in each leg acts along its axis. D 7.5 m 4.5 m 3 m 3 m B 4.5 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.42P: The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a...

See similar textbooks

Related questions

Q: A disk of radius R = 2 m, whose mass is distributed homogeneously and equals 6 kg, is suspended at…

A: R=2mm=6kgk=0.5 Nm/radl=1mb=Ns/m

Q: *5-108. If the solid shaft is made from red brass C83400 and it is subjected to a torque T = 6 kip…

A: From the given condition angle of twist is same for AB and…

Q: Suppose that L = 235 mm. (Figure 1) Figure 100mm 150 mm 250 mm <10f1 L 130 mm 150 mm Part A Locate…

A: The length L is 235 mm

Q: 1. Kinematics is concerned with: a. The forces that cause acceleration The geometric aspects of…

A: The correct answer is option c. c. Velocity, acceleration, displacement. Kinematics is the branch of…

Q: 100 mm 50 mm 100 mm 60 mm 150 mm 50 mm 50 mm 50 mm X

A: To find: The moments of inertia about the centroid of the shape.

Q: Assuming the pulley system below is weightless and frictionless, determine the reaction force (FR)…

A: According to the given data W=1525 N We need to find FR

Q: 4. A particle moves along a horizontal path with its velocity varying with time as shown. The…

A: According to the guidelines, we can solve only one question at a time. You are requested to post…

Q: A mass of 450 kg has been hung from the end of a metal wire whose initial length is 1.8 meters and…

A: According to the question m=450kg F=mg=450x9.81= 4414.5 N D=1.5 mm L=1.8m=1800mm ∆L=1.25=12.5mm We…

Q: Explain what a "heated zone" is, how it operates, and any potential restrictions.

A: Heat source:-Any appliance, method, or fuel that generates heat to warm a room or deliver hot water…

Q: I'm sorry instead of 695 it was 605.

Q: 12. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630…

A: The force applied on the right side of the lever is, P= 200 lb The length of the steel wire attached…

Q: What factors the linker considers while deciding between these two apparently similar processes?

A: Linkers are typically used in software development to combine object files or libraries into a…

Q: 3 درا 5 3 m 400 N/m -3 m B

Q: Two cables BC and BD are used to support the fixed bracket at B as shown. Cable BD exerts a tension…

Q: a) Determine the pulling force F on each of the following four pulleys. 1 2 3 4 E=100 N F F-100 N…

A: According to the given data A free-body diagram for the tension in the cable is shown below picture…

Q: फो

Q: How many poles are in the right half-plane, the left half-plane, and on the jw-axis for the…

A: Given Data: To Find: Poles in the right half-plane, poles in the left half-plane and poles on the…

Q: The man in the figure draws the rope tied at point A. It pulls with a force of F=150 N. According to…

A: According to the given data in the question F=150N From the A to B We need to find The Moment of…

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: Consider a 0.6-m × 0.6-m thin square plate in a room at 30°C. Both sides of the plate are maintained…

A: Given: The average film temperature. The properties of air at 60°C.

Q: The rod AC can move frictionlessly through the sleeve B. The sleeve C travels frictionlessly along…

Q: We need to build a heatable warehouse with a capacity of 2000 cubic meters. Because the building is…

A: Volume = 2000 m3 Slope of roof = 45° We need to find: actual width (a), length (b) and roof ridge…

Q: The following mass-and-spring system has stiffness matrix K. For the mks values, find the two…

A: m1=1, m2=5 k1=3, k2=15, k3=15 K=-k1+k2k2k2-k2+k3

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 870 N, a =…

A: Force F=870N, a=630 mm b=285 mm θ=320 ∅=590

Q: Find the center of mass of the lamina bounded by the graphs of the equations x = 9-y² and x = 0 for…

A: given x = 9 - y² x = 0 ρ = kx

Q: Determine the angular velocity of the gear and the velocity of its center O at the instant shown. 4…

Q: Problem (4) For the control system shown in Fig. 4, design a compensator such that the static…

A: static velocity error constant Kv = 20 sec-1

Q: A dormitory room measures 4m x 6m x 6m. A student turns on a 150 watts fan before leaving the room…

Q: Determine the forces in members AB, AC, and AD. Forces are positive if in tension, negative if in…

A: According to the given data A loading structure ABCD is given We need to find The force in the…

Q: **2.35 A tank of 2 m length and of cross section shown in Fig. 2.36 contains water. The tank is made…

Q: Question 2 An aircraft engine operates on a simple ideal Brayton cycle with a pressure ratio of 10.…

A: The cycle is the Brayton cycle. The mass flow rate of air is m=1 kg/s The air at beginning of…

Q: An ideal air-standard regenerative Brayton cycle produces 10 MW of power. Operating data at…

A: The mass flow rate, rate of heat transfer, and thermal efficiency. Given: The power produced is…

Q: Presume that we have 100 grams of an alloy with overall chemical composition of 90 wt. pct. tin and…

A: The mass of alloy, m = 100 gm The composition of the alloy = 90 wt%Sn and 10 wt% Pb The temperature…

Q: Each cylinder of a four-cylinder four-stroke petrol engine has a bore diameter of each is 55 mm and…

A: Given Dimensions of the cylinder Diameter of the bore D=0.055m Stroke Length of the piston L=0.280m…

Q: The simple beam shown carries a uniform load w, = 10 kN/m. The dimensions a, b, c, and d are 0.6 m,…

A: wo=10 kN/ma=0.6mb=0.4mc=50mm=0.050md=80mm=0.080m

Q: A simple ideal Rankine cycle which uses water as the working kPa. The boiler produces a 10 MPa…

A: Given data is

Q: 5. A filter 6. Components valve in a pressure filter avoids element collapse and dirt extrusion.…

A: The correct for the blanks.

Q: Shown is a chain carrying a load P of 10 kN. If the allowable stress in the chain is 225 MPa, what…

A: Given Load P =10 kN Allowable stress = 225 MPa

Q: A piece of corroded steel plate was found in a submerged ocean vessel. It was estimated that the…

A: The area of plateA=16 in2 The amount that corroded away A=2.9 kg The corrosion penetration rate…

Q: 2. Determine the clamping force on the bolt and reactions at pin A for the pliers shown.

A: It is required to determine the force on the bolt and reactions at pin A, given that the applied…

Q: The state of stress at a point is shown on the element. Determine (a) the principal stress and (b)…

A: Given: The stress in horizontal direction σx=-30 ksi. The stress in vertical direction is σy=0 ksi.…

Q: 19. A compound shaft made of two different materials is load with T = 24 N-m as shown. L₁ = L₂,…

A: According to the question Torsional Load T = 24 N-m Length of material 1 L1= Length of material 2 L2…

Q: Compute the maximum percent overshoot 100Mp and the 2% settling time ts that correspond to wn = 1…

A: To find: The value of maximum percent overshoot; The value of setting time. Given: The value of…

Q: a) How can we test which can withstandthe most stress, a length of spider web thread or a steel wire…

A: Formula used: Write the expression for the stress. σ=E×ε Here, σ is stress, E is plastic modulus and…

Q: The stress case at a point of a body is shown on the element below. Determine the principal normal…

A: The principal normal stresses, principal shear stresses, and the directions. Given: The stress in…

Q: if 2. m= yağ-kütle sönümleyici sistemi aşağıda verilmiştir. 10 kg. b 30 N-s m. k 1000 Nm. P ||| 10N…

A: Please refer below Images for the solution.

Q: A (2 kg) mass attached to a linear elastic spring of stiffness (k 200 N/m) is released from rest…

A: Write the given data. m=2 kgk=200 N/mx=10 cm=0.1 mμk=0.1 It is required to determine the damping…

Q: Q1 For the pin-jointed truss shown below, with a vertical load applied at joint 1, determine: (i)…

A: For the pin-jointed truss shown below, with a vertical load applied at joint 1, To find: (i)The…

Q: A particle is constrained to travel along the path. If x = (4t4) m, where t is in seconds, determine…

Q: The x-axis of this graph refers to which of the following? Stress (N/mm) Macroscopic failure…

A: Given data is

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

The shear leg derrick is used to
haul the 350-kg net of fish onto the
dock. Determine the compressive
force along each of the legs AB and
CB and the tension in the winch
cable DB. Assume the force in
each leg acts along its axis.
D
7.5 m
A
Z
4.5 m
3 m
3 m
B
4.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given Data

VIEW

Step 2: Force Body Diagram

VIEW

Step 3: Calculations of compressive and tensile forces

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2.0 m 100 kg 2.0 m 0.5 m 1.5 m 1.5m The pulley at E is frictionless. Point B is a pinned connection; support A is a fixed support. The pin at C is in a smooth slot. Determine the magnitude of normal force the pin C exerts on the smooth slot, = N. Determine the magnitude of of the y-component of the reaction force at B, By= . N. Determine the magnitude of of the x-component of the reaction force at B, Bx= N. O O :
Determine the tensions in the cable, normal force in the smoothsurfaces and the angle of inclination of the surface in the right ifthe block in the left and right weigh 300N and 500N,respectively. (Assume frictionless pulley)T =NA =NB =θB =
A 415 kg safe is hanging from the apparatus below. Determine the tension in the cable. Dimension a=1.9 m and dimension b=2.5 m. The mass of the beam is 85 kg. Use g = 10 N/kg. Hint: Take torques about the hinge and use the perpendicular lever arm version of the torque equation (the sin theta version will work but will require more calculation).
3) The shear leg derrick is used to haul the 200-kg net of fish onto the dock. Determine the compressive force along each of the legs AB and CB and the tension in the winch cable DB. Assume the force in each leg acts along it axis. D 5.6 m 4 m B $2 m A 2 m 4 m
2.0 m 100 kg 2.0 m 0.5 m 1.5 m 1.5 m The pulley at E is frictionless. Point B is a pinned connection; support A is a fixed support. The pin at C is in a smooth slot. s in: Determine the magnitude of of the x-component of the reaction force at A, Ax= N. Determine the magnitude of of the y-component of the reaction force at A, Ay= N. Determine the magnitude of of the external moment applied at A, MA= Nm. O O :
The force P on the handle of the positioning lever produces a vertical compression of 56lb in the coiled spring in the position shown. Determine the magnitude of the corresponding force exerted by the pin at O on the lever. Assume a = 3.4in. b = 8.6in.
The shear leg derrick is used to haul the 200-kg net of fish to the dock. Determine the compressive force along eanch of the legs AB and CB and the tension in the winch cable DB. Assume the force in each leg acts along its axis. a=4.6 m b=3.8 m c=2.1 m D x a A b B b
The shear leg derrick is used to haul the 200-kg net of fish to the dock. Determine the compressive force along eanch of the legs AB and CB and the tension in the winch cable DB. Assume the force in each leg acts along its axis. a= 5.7 m b= 3.7m c= 2.2m D a b B b
Determine the tensions in the cable, normal force in the smoothsurfaces and the angle of inclination of the surface in the right ifthe block in the left and right weigh 300N and 500N,respectively. (Assume frictionless pulley)
The bucket weighs 15 Ibs. determine the forces in the cables. 2.5 ft- 4.5 ft 3 ft 1,5 ft 3 ft -1.5 ft-
The horizontal force P is applied to the handle of the puller. Determine the resulting tension T in the chain in terms of P .
Find the forces in each member and specify if it is in tension or compression. At E is pin support and at D is link support. 5 m -link support B 5 m 5 m 5 m 5 m 5 m 5 m E 30 kN 20 kN