The shaft is made of A-36 steel and has a diameter of 70 mm. It is fixed at B and the support at A has a torsional stiffness of k = 0.5 MN m/rad. (Figure 1) Figure 4 kN·m 2 kN·m 600 mm 600 mm < 1 of 1 > 600 mm ▾ Part A If it is subjected to the gear torques shown, determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tabs= Value Units Submit Previous Answers Request Answer × Incorrect; Try Again; 3 attempts remaining Provide Feedback

The shaft is made of A-36 steel and has a diameter of 70 mm. It is fixed at B and the support at A has a torsional stiffness of k = 0.5 MN m/rad. (Figure 1) Figure 4 kN·m 2 kN·m 600 mm 600 mm < 1 of 1 > 600 mm ▾ Part A If it is subjected to the gear torques shown, determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tabs= Value Units Submit Previous Answers Request Answer × Incorrect; Try Again; 3 attempts remaining Provide Feedback

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.3P: A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A...

See similar textbooks

Similar questions

A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 Ib-A 50 Ib-ft 70 Ib-ft (1) (2) 30 Ib-f (3) 827 psi O 880 psi O 956 psi 691 psi O 739 psi
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a wall thickness of 9 mm. Segment (2) has an outside diameter of 139 mm and a wall thickness of 11 mm. The shaft is subjected to torques TB = 47 kN-m and Tc = 24 kN-m, which act in the directions shown. Determine the maximum shear stress magnitudes 7₁, 72 in each shaft segment. Answers: T1 = i T2 = i (1) (2) MPa. MPa.
PROBLEM 1. The shafts are made of A-36 steel and both have 100 mm diameter. If a torque of 60 kN.m is applied to end E and 25 kN.m to the D gear as shown in the figure, determine the angle of twist of the section at E of the DE shaft. 0.75 m 0.75 m A B 150 mm 25 kN-m 300 mm 60 kN.m 1.25 m E
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 140-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of TA = 260 N-m. The shaft is machined from steel with Sy = 400 MPa and Sut = 560 MPa. Assume factor of safety and all other factors as (one) 1,. Determine the minimum allowable diameter of the 100-mm section of the shaft for infinite life (selectec criter sould be written at the begining of the solution) 250 mm 100 mm 20
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D as shown. Determine the maximum shear stress in the shaft and the rotation angle for gear A. G = 80 GPa 40 N•m 280 N m 0.5 m 150 N-m B 0.3 m P. 100 mm 0.4 m (a)
A 40-mm-diameter solid shaft is subjected to an axial force of P = 2790 N, a vertical force of V = 1650 N, and a concentrated torque of T = 50 N-m, acting in the directions shown. Assume L = 130 mm. Determine the horizontal shear stress τxy at point K.
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which 250 mm has a 150 mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T = 340 N. m. The shaft 100 mm is machined from steel with S, = 420 MPa. Using a factor of safety of 2.5, determine the minimum allowable diameter of the 250 mm section of the shaft based on a static yield analysis using the distortion energy theory and maximum shear stress theory.
A shaft ABCD is fixed at end D and has torques acting at points A, B, and C as shown below. The bearing support between A and B allows free rotation. If we know that A = −0.382 rad, A/B = 0.358 rad, and B/C = −0.233 rad, calculate the absolute twist of the shaft at point C(oc) and enter it in rad (radians) correct to 3 significant digits below. Make sure to include the sign if it is negative noting that CCW rotations are positive and CW rotations are negative. 150 N.m 280 N.m B 40 N-m D