The same shaft with keyway considered here again. Suppose that the shaft is working in ambient temperature and the following correction factors are obtained: CF-0.84 CS=0.88 Ce=0.64 Find the un-corrected fatigue strength of the material in MPa, if the corrected fatigue strength from the Goodman diagram obtained as to be Sf=310 MPa (Hint: round your answer to 4 digits after decimal point).

The same shaft with keyway considered here again. Suppose that the shaft is working in ambient temperature and the following correction factors are obtained: CF-0.84 CS=0.88 Ce=0.64 Find the un-corrected fatigue strength of the material in MPa, if the corrected fatigue strength from the Goodman diagram obtained as to be Sf=310 MPa (Hint: round your answer to 4 digits after decimal point).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4) Compute the fatigue life of a rotating hub and shaft assembly, if at a critical point in the shaft, the state of stress is described by σxx,max = 1000 MPa, σxx,min=-800 MPa, Txy,max = 300 MPa, Txy,min = -100 MPa, and σyy = σzz = Txz = σyz = 0. Employ the maximum shear stress thory of failure together with modified Goodman criterion. Take σ₁ = 2400 MPa and the fatigue-strength reduction factor K=1. [Use fracture stress as 0.9 times the ultimate stress, endurance stress as (1/3) times K times the ultimate stress, N = 103 cycles and Ne=108 cycles]
Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonrotating orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. 6T td7 (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.
Question Three An intermediate shaft is running at constant speed as shown in Figure 3. The shaft to be made from AISI1040 cold rolled. The shaft is subjected to torque which is fluctuates from Tas to 0.5 Trux torque in phase with a steady bending. The reliability is 90% and stress concentration factor Ki = 1.5 for bending and Ks = 2 for torsion for 3 mm fillet radius. a. Use modified Goodman theory to determine the minimum shaft diameter required to obtain the fatigue factor of safety of 2.5 b. Calculate Langer first -cycle-yielding factor of safety F. = 6 kN R75 mm R50 mm 150 mm 350 mm F= 9 kN 250 mm Figure 3
The figure shows a shaft mounted in bearings at A and D and having pulleys at B and C. The forces shown acting on the pulley surfaces represent the belt tensions. The shaft is to be made of AISI 1035 CD steel. The shaft is rotating at speed of 1000 rpm. Find the minimum factor of safety for fatigue based on infinite life. If the life is not infinite, estimate the number of cycles. Be sure to check for yielding. Take shaft diameter to be 1.5 inches.
2. At a machined shaft shoulder the small diameter d is 25mm the large diameter D is 40mm, and the fillet radius is 2.5 The bending moment is 2300N mm and the steady torsion moment is 1800 N mm The heat-treated steel shaft has an ultimate strength of Sut- 850Mpa The reliability goal is 099 (ka- 0.786, kb 0.870, ke 0.814) Determine the fatigue factor of safety of the design described in this section
42. The static deflection at the center of the steel shaft in Fig. 3-53 is equal to 0.35 mm. Find the value of the critical speed. Shaft is steel. Ans. n = 1810 rpm. Design of Shafts Chap. 3 248 t. 50 30 1"dia 10" 10" Figure 3-52 Problem 41. 10 kg 10 kg C B 375 600 mm 375 Figure 3-53 Problem 42.
Compute the twisting and bending moments of the shaft (AISI 4140 steel) given the following parameters: Shaft length = 42 in Shaft diameter = 0.945 in Force = 245.25 N Torque = 79.71 Nm
Use the general shaft layout given and determine critical diameters of the shaft based on infinite fatigue life with a design factor of 1.5. Check for yielding. Check the slopes at the bearings for satisfaction of the recommended limits in Table 7-2. Assume that the deflections for the pulleys are not likely to be critical. 10 in 500 lbf 75 lbf 8-in dia. Bearing at O 10.0" 500 lb d 75 lb Material 1040 Q and T 18 in Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions in the belt at pulley Bare T₁ and T2, where T₁ is 15% of T2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 10-in dia. 12 in T₂ 8.0⁰ T₁ 18.0" 10.0" I B pulley diameter = 8.0" Sut 113 kpsi T2 T1 pulley diameter = 10.0" Sy 86 kpsi 12.0" Bearing at C Using the DE-Goodman criteria and a design factor of 1.5, calculate the diameter based on the shaft's loadings…
with diameter d = 38 mm transmits 37 kW to a gear Calculate the required speed of rotation (number of at B. The allowable shear stress in the steel is 40 MPa. X7-3 A motor driving a solid circular steel shaft revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm B
The shaft shown in the figure below and rotating at a speed of 1 radian / sec transmits 9 kW of power from the gear at the B point to the pulley at the D point. Manufactured from cold drawn AISI 1040 steel, the shaft is machined to the given dimensions and bedded from A and C points. The highest working temperature of the spindle is 50 ° C. At point D; Since (d2 / d3 = 1.1) and (r /d = 0.1), determine the diameter d3 of the shaft using Goodman's theory. (kb = kc = kf = 1, q = 0.8 and qs = 0.9) 200 mm 140 mm 60 mm F1= 5F Fa Kasnak 160 Ry F2 = F Dig!! Ray Ray
Use the general shaft layout given and determine critical diameters of the shaft based on infinite fatigue life with a design factor of 1.5. Check for yielding. Check the slopes at the bearings for satisfaction of the recommended limits in Table 7-2. Assume that the deflections for the pulleys are not likely to be critical. 500 lbf 75 lbf 8-in dia. Bearing at O 500 lb d 10.0" 75 lb Material 1040 Q and T 18 in Use the following shaft layout assuming a pulley transmits torque through a key and keyseat at location A to another pulley at location B. Assume the tensions in the belt at pulley B are T₁ and T2, where T₁ is 15% of T2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 10-in dia. 12 in T₂ T₁ The mean torque is 0 lb-in. The alternating torque is 2125 lb-in. The mean moment is 0 lb-in. The alternating moment is 5000 lb-in. 18.0" pulley diameter = 8.0" Sut 113 kpsi 10.0 B T2 T1 pulley diameter = 10.0" Sy 86 kpsi 12.0"…
The nodal point on the shaft section is subjected to opposed shear stress, this leads to decrease in the effect of torsional shear stress which increases the fatigue life of the shaft. Select one: O True O False