The rotating shaft shown is subjected to a constant force. Shaft material is AISI 1020 cold drawn steel. The shaft was turned on a lathe using standard carbide tooling. No heat treatment of the shaft was performed. Assume 99% reliability based on material property data. Shaft dimensions are shown in the illustration below. All dimensions in mm. External force is 3.927 KN. Calculate the highest alternating stress in the shaft, in MPa.

The rotating shaft shown is subjected to a constant force. Shaft material is AISI 1020 cold drawn steel. The shaft was turned on a lathe using standard carbide tooling. No heat treatment of the shaft was performed. Assume 99% reliability based on material property data. Shaft dimensions are shown in the illustration below. All dimensions in mm. External force is 3.927 KN. Calculate the highest alternating stress in the shaft, in MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075. The shaft is 960 mm in length, 40 mm OD and 20 mm ID. The threaded end of the shaft is M30X3.5. What would be the recommended torque for the shaft, with the dissimilar metals.
Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonrotating orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. 6T td7 (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.
Please give step by step solution other wise don't answer I will report to Bartley team. A medium carbon steel shaft transmits 25 kW at 450 r.p.m. The diameter of shaft is 40 mm. A square key is used whose one side is equal to 1/4th of the shaft diameter and whose length is equal to 1.5 times of the shaft diameter. Find the dimensions of the key and check the key for the induced shearing stress and crushing stress.
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
The shaft below is an engine component that is rotating. It is machined from an unknown ductile material with a measured ultimate tensile strength of 700 MPa. Answer the questions below assuming a desired reliability of 99% and a fatigue fraction, f, of 0.9. Round all values and answers to 2 decimal places Determine the maximum stress in the shaft due to the applied loading (hint: what is the maximum moment?) Estimate the endurance limit (hint: what is the relationship between Se and Sut and don’t forget any necessary modifying factors.) Determine the number of cycles to failure.
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
topic: torsion in circular shafts The hollow shaft used in the system has the following conditions: Outer diameter (Ø): 150 mm Ø Allowable Shearing Stress: 85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
! Required information A 24-mm-diameter uniform steel shaft is 600 mm long between bearings. Take the value of acceleration due to gravity g to be 9.81 m/s2, the value of y for carbon steel to be 76.5 × 103 N-m-3, and the value of Eto be 207 x 10⁹ N/m². NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the critical speed of the shaft in rads/s? (You must provide an answer before moving to the next part.) The critical speed of the shaft is 847.5 rad/s.
A shaft is designed to transmit power of 100 kW at 180 rpm. The allowable shear stress is 50MPa and modulus of rigidity of 80 GPa. The angle of twist is not to exceed to 1° in 4-meter length A. Calculate the diameter of the shaft in inches. B.If the shaft in A is to be fitted to a hub with material SAE 0105 and fit classification of FN3, what will be the maximum and minimum stresses based on the interference of metal.
What is the minimum diameter in meter of a solid steel shaft that will not twist through more than 3˚ in 6 meter length, when subjected to a torque of 14 kN m. Use G of 83 Gpa.
The shaft whose torque varies from 2000 to 6000 in-lbs has 1 ½ inch in diameter and 60,000 psi yield strength. Compute for the shaft mean average stress. A. 6036 psi B. 6810 psi C. 5162 psi D. 5550 psi Please solve the Problem elaborately and Refer Machine Elements and Stresses Equations from the figures or use other shortcut Methods you have or you may Solve both or in more different methods the better ?. Your solution will be use as reference for my Future Board Exam preparation/review/study. Thank you so much dear your work will be appreciated much and rated excellently.
A solid circular drive shaft connects a motor to gears B and C. The drive shaft is steel (G= 66 GPa) with a diameter of d=35 mm. 600 N-m A 200 N-m (1) (2) 100 mm C. 300 mm