The roof system of an office building consists of a 4 in. thick reinforced concrete slab resting on four steel beams( 16.2 in. ) 52A, which are supported by two steel girders (42.9 in.) 5 2 A . The girders, in turn, are supported by four columns, as shown in Fig. P2.8. Determine the dead loads acting on the girder AG -20 ft-

The roof system of an office building consists of a 4 in. thick reinforced concrete slab resting on four steel beams( 16.2 in. ) 52A, which are supported by two steel girders (42.9 in.) 5 2 A . The girders, in turn, are supported by four columns, as shown in Fig. P2.8. Determine the dead loads acting on the girder AG -20 ft-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two simply supported beams B, and Bz have spans l and 21 respectively. Beam B, has a cross-section of Ix1 units and beam b2 has a cross-section of 2 x 2 units. These beams are subjected to concentrated loads w each at the centre of their spans. The ratio of the maximum flexural stress in these beams is A. 4 B. 2 1 2 D. 4 C.
The roof of a single-story storage building shown is subjected to a uniformly distributed load of 2.4 kPa over its surface area. Beam BE is simply supported. Likewise, girders AC, CF, FD and AD are simply supported on columns A, C, F, and D. Girder Floor beam Column 6 m E 2 at 4 m = 8 m Which of the following most nearly gives the resulting axial load (kN) at column at C? B
MEMERE 2.4 m 8 kN B 2.4 m 8 KN E 3.6 m 2.4 m 8 kN C 2.4 m Determine the force in each member of Pratt truss in the roof shown the figure
The roof of a single-story storage building shown is subjected to a uniformly distributed load of 2.4 kPa over its surface area. Beam BE is simply supported. Likewise, girders AC, CF, FD and AD are simply supported on columns A, C, F, and D. Girder Column Floor beam B 6 m E -2 at 4 m 8 m- Which of the following most nearly gives the maximum bending moment (kN-m) in beam AC?
Prob. 1 Four 50 mm x 200 mm dressed planks are used to carry a super imposed load of "W" kN/m. The allowable bending stress of the plank is 8.30 MPa. How should the four planks be framed to give the maximum stiffness as a beam? Determine also the safe uniform "W" kN/m that this beam could carry if the span is 6 m and is assumed to be simply supported. diagram 1 40.5 40.5 40.5 40.5 162 diagram 2 134.25 268.5 187.50 187.50 40.5 187.5 40.5
Q1: Determine the force in each member of the double-pitch roof truss shown. State whether each member is in tension or compression. 3 m 3 m -4 m. 4 m-4 m- 1.75 kN 2 kN 1.5 kN 2 kN 1 kN 0.75 kN 6 m B E 6 m 6 m 6 m
I. Method of Joints 1. The portion of truss shown represents the upper part of a power transmission line tower. For the given loading, determine the force in each of the members located above HJ. State whether each member is in tension or compression. 1.60 m -221 m- -2.21 m- To60m 10.60 m 1.20 m 12 kN 12 kN L f060 m To.60m -2.97 m- 1.20 m 12EN 1.2 KN To.00m f0.60 m 12 kN 1.2 kN 2. The truss shown in figure is pin connected only at the lettered joints. Find the force acting in each member. 12 H E 400 Ib 600 Ib 4 panels @18' 72"- 800 Ib
The floor system of a factory consists of a 5”-thick normal weight reinforcedconcrete slab resting on four steel floor beams (A = 14 in2) that, in turn, aresupported by two steel girders (A = 40 in2), as shown in the plan below.a. Should this slab be idealized as one-way spanning or two-way spanning?b. Draw the free-body diagram for the dead loads on beam BF and label themagnitude of all loads.c. Draw the free-body diagram for the dead loads on girder AD and label themagnitude of all loads.d. What is the axial load carried by column A?
2-15. A truss is loaded as shown in Fig. P 2-15. Determine the resultant load on the truss. 5000 6000 2000 6 Panels 10' • 60' 10004
2.) The Pratt roof trusses are uniformly spaced every 3.60 m. The deck, roofing material, and the purlins have an average weight of 0.15 kN/m^2. The building is located in the hills where the anticipated wind load is 2.10 kN/m^2. The wind load is assumed act perpendicular towards the top chord of the roof (side AHG only). Considering the given loads, determine the following: a.) Equivalent concentrated load on Joint A, H, G, F and E due to dead load b.) Equivalent concentrated load on Joint A, H and G due to wind load c.) Force in each member due to dead load and wind load. Neglect the weight of the truss members and assume A is pinned and E is a roller
Q2. Determine the force in each member of the double-pitch roof truss as shown in Fig.2. State whether each member is in tension or compression. 3 m, 3 m -4 m→-4 m--4 m- 1.75 kN 2 kN 1.5 kN 2 kN _0.75 kN 6 m 1 kN D В A E - 6 m. 6 m -6 m.
Two wires support a weight W. The stresses in the wires AB and AC are not to exceed 133 MPa and 195 MPa, respectively. The cross sectional area of the two wires are 492 mm² for AB and 214 mm² for AC. Wire AB is inclined 27-degrees with the horizontal and wire AC is inclined 47-degrees with the horizontal. Give the largest weight W (kN) that can be supported by the wires?