The rigid body shown is rotated about an axis perpendicular to the paper and through the point P. If M = 0.40 kg, a = 30 cm, and b = 50 cm, how much work is required to take the body from rest to an angular speed of 5.0 rad/s? Neglect the mass of the connecting rods and treat the masses as particles. 3M 3.1 J 0 2.9 J 02.6J 1.6 J 3.4 J M p q# 9 p. 242 chap 7

The rigid body shown is rotated about an axis perpendicular to the paper and through the point P. If M = 0.40 kg, a = 30 cm, and b = 50 cm, how much work is required to take the body from rest to an angular speed of 5.0 rad/s? Neglect the mass of the connecting rods and treat the masses as particles. 3M 3.1 J 0 2.9 J 02.6J 1.6 J 3.4 J M p q# 9 p. 242 chap 7

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter11: Angular Momentum

Section: Chapter Questions

Problem 77P: The axis of Earth makes a 23.5 angle with a direction perpendicular to the plane of Earth’s orbit....

See similar textbooks

Similar questions

To develop muscle tone, a woman lifts a 2.00-kg weight held in her hand. She uses her biceps muscle to flex the lower arm through an angle of 60.0°. (a) What is the angular acceleration if the weight is 24.0 cm from the elbow joint, her forearm has a moment of inertia of 0.250kg-m2 and the net force she exerts is 750 N at an effective perpendicular lever arm of 2.00 cm? (b) How much work does she do?
A cylinder with rotational inertia I1=2.0kgm2 rotates clockwise about a vertical axis through its center with angular speed 1=5.0rad/s . A second cylinder with rotational inertia I2=1.0kgm2 rotates counterclockwise about the same axis with angular speed 2=8.0rad/s . If the cylinders couple so they have the same rotational axis what is the angular speed of the combination? What percentage of the original kinetic energy is lost to friction?
The blades of a wind turbine are 30 m in length and rotate at a maximum rotation rate of 20 rev/min. (a) If the blades are 6000 kg each and the rotor assembly has three blades, calculate the angular momentum of the turbine at this rotation rate. (b) What Is the torque require to rotate the blades up to the maximum rotation rate in 5 minutes?
The axis of Earth makes a 23.5 angle with a direction perpendicular to the plane of Earth’s orbit. As shown below, this axis precesses, making one complete rotation in 25,780 y. (a) Calculate the change in angular momentum in half this time. (b) What is the average torque producing this change in angular momentum? (c) If this torque were created by a pair of forces acting at the most effective point on the equator, what would the magnitude of each force be?
A block of m = 12 kg is placed against the vertical front of a cart as shown below. What acceleration must the cart have so that block A does not fall? The coefficient of static friction between the block and the are is m, = 0.4. a. 24.5 m/s2 O b. none of these О с. 36.8 m/s? O d. 6.1 m/s? О е. 18.4 m/s?
A person spins a large grindstone 0.320-m radius, from rest, by placing his hand on its edge and exerting a force through part of a revolution as shown in the figure. 1. How much work is done if he exerts a force of 200 N through a rotation of 1.0 rad (57.3)? 2. The force is kept perpendicular to the grindstone at the point of application, and the effects of friction are negligible. Calculate the final angular velocity if the grindstone has a mass of 85.0kg. The grindstone is considered as a disk.
A particle of mass m is attached to the end of a string and moves in a circle of radius r on a frictionless horizontal table. The string passes through a frictionless hole in the table and, initially, the other end is fixed. a. If the string is pulled so that the radius of the circular orbit decreases, how does the angular velocity change if it is wo when r = ro? 6. b. What work is done when the particle is pulled slowly in from a radius ro to a radius ro/2?
The following figure shows the cross section of a cylinder of radius 7.5 m rotating about its axis at :9.0 rad/s. The speed of the point P is rad/s 212.06.a O Can not be determined .b O m/s 212.06.c O m/s 67.50.d O rad/s 67.50.e O
The L-shaped object in the figure(Figure 1) consists of three masses connected by light rods. Find the work that must be done on this object to accelerate it from rest to an angular speed of 2.00 rad/sr about the x axis. About the y axis. About the z axis (which is through the origin and perpendicular to the plane of the figure).
The puck in the figure below has a mass of 0.224 kg. Its original distance from the center of rotation is 40.0 cm, and it moves with a speed of 70.0 cm/s. The string is pulled downward 15.0 cm through the hole in the frictionless table. Determine the work done on the puck. Hint: Consider the change in kinetic energy of the puck. J m P
The following figure shows the cross section of a cylinder of radius 4.4 m rotating about its axis at 8.3 rad/s. The speed of the point P is: P O a. 114.73 rad/s O b. Can not be determined O c. 114.73 m/s O d. 36.52 rad/s O e. 36.52 m/s
Peter propels a penguin with mass 10.0kg from 2.50m above the ground at an angle 30.0o from the horizontal axis (ground), with an initial speed of 15.0 m/s. Assuming the penguin remains rigid (scared, so assume the particle model!) and ignoring any rotational effects, Using the isolated system model, what is the maximum potential energy of the penguin? a. 1370 Joules b. 1125 Joules c. 245 Joules d. 2250 Joules