The rigid bar in (Figure 1) is pinned at A andsupported by two aluminum rods, each having adiameter of 1.5 in., a modulus of elasticityE-10(10³) ksi, and yield stress of(ay)=44 ksiFigureBED-1.5 ft1.5 ft220 kip1 ft2 ft1 of 1 >1 ftPart AIf the bar is initially vertical, determine the angle of tilt of the bar when the 20 kip load is applied.Express your answer to three significant figures and include appropriate units.HA→?ValueUnitsSubmitProvide FeedbackRequest Answer

Answered: Image /qna-images/answer/607d8cf2-d4ea-4afa-aa8c-525c2f8e5228.jpg

The rigid bar in (Figure 1) is pinned at A and supported by two aluminum rods, each having a diameter of 1.5 in., a modulus of elasticity E-10(10³) ksi, and yield stress of (ay)=44 ksi Figure 1 of 1 B J E 1.5 ft 1.5 ft 20 kip 1ft 2 ft 1 ft Y Part A If the bar is initially vertical, determine the angle of tilt of the bar when the 20 kip load is applied. Express your answer to three significant figures and include appropriate units. HA → ? Value Units Submit Provide Feedback Request Answer

The rigid bar in (Figure 1) is pinned at A and supported by two aluminum rods, each having a diameter of 1.5 in., a modulus of elasticity E-10(10³) ksi, and yield stress of (ay)=44 ksi Figure 1 of 1 B J E 1.5 ft 1.5 ft 20 kip 1ft 2 ft 1 ft Y Part A If the bar is initially vertical, determine the angle of tilt of the bar when the 20 kip load is applied. Express your answer to three significant figures and include appropriate units. HA → ? Value Units Submit Provide Feedback Request Answer

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.7P: Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and...

See similar textbooks

Similar questions

A solid bar of circular cross section (diameter d) has a hole of diameter d/5 drilled laterally through the center of the bar (sec figure). The allowable average tensile stress on the net cross section of the bar is s allow. (a) Obtain a formula for the allowable load P allowthat the bar can carry in tension. (b) calculate the value of P allowif the bar is made of brass with a diameter d = 1.75 in. and s allow= 12 ksi. Hint: Use the formulas of Case 15. Appendix E.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A prismatic bar of length L = 1.8 m and cross-sectional area A = 480 mm" is loaded by forces P{= 30 kN and A = 60 kN (see figure) The bar is constructed of magnesium alloy having a stress-strain curve described by the Ram berg-Osgood equation: 45.000 618 UW id which u has units of mega pascals (MPa). (a) Calculate the displacement 8t- of the end of the bar when the load P:acts alone. (b) Calculate the displacement when the load P, acts alone. (c) Calculate the displacement when both loads act simultaneously.
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
AW310 × 74 wide-flange steel column with length L = 3.8 m is fixed at the base and free at the top (see figure). The load P acting on the column is intended to be centrally applied, but because of unavoidable discrepancies in construction, an eccentricity ratio of 0.25 is specified. Also, the following data are supplied: E = 200 GPa, y = 290 MPa, and P = 310 kN. What is the maximum compressive stress max in the column? What is the factor of safety n with respect to yielding of the steel?
A W410 × S5 steel column is compressed by a force P = 340 kN acting with an eccentricity e = 38 mm, as shown in the figure. The column has pinned ends and a length L. Also, the steel has a modulus of elasticity E = 200 GPa and yield stress y= 250 MPa. P = 340 kN If the length L = 3 m, what is the maximum compressive stress maxin (he column? If a factor of safety n =2.0 is required with respect to yielding, what is the longest permissible length Lmaxof the column?
A square aluminum bar with pinned ends carries a load P = 25 kips acting at distance e = 2,0 in. from the center (sec figure). The bar has a length E = 54 in. and modulus of elasticity E = 10,600 ksi. If the stress in the bar is not to exceed 6 ksi, what is the minimum permissible width bminof the bar?
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.